The shear stress level in arteries is regulated such that, when a higher (or lower) shear level is sensed by theendothelium of an artery (the cells that line the inner wall of the artery), the artery alters its radius so that theshear level returns to its optimal value. This optimal value, to, is relatively constant through the arterial tree.On the basis of this criterion, determine how the flow rate depends on the artery diameter in such an arterialtree. You may assume steady flow conditions.

Shear stress is the force per unit area parallel to the direction of fluid flow in a fluid, such as…

The shear stress level in arteries is regulated such that, when a higher (or lower) shear level is sensed by the endothelium of an artery (the cells that line the inner wall of the artery), the artery alters its radius so that th shear level returns to its optimal value. This optimal value, to, is relatively constant through the arterial tre On the basis of this criterion, determine how the flow rate depends on the artery diameter in such an arteria tree. You may assume steady flow conditions.

The shear stress level in arteries is regulated such that, when a higher (or lower) shear level is sensed by the endothelium of an artery (the cells that line the inner wall of the artery), the artery alters its radius so that th shear level returns to its optimal value. This optimal value, to, is relatively constant through the arterial tre On the basis of this criterion, determine how the flow rate depends on the artery diameter in such an arteria tree. You may assume steady flow conditions.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.3 An incompressible liquid of density p and viscosity u flows in a thin film down a glass plate inclined at an angle to the horizontal. The thickness a of the fluid film normal to the plate is constant, the velocity is everywhere parallel to the plate, and the flow is 2-D and steady. Neglect viscous shear between the air and the moving liquid at free surface. Determine the variation in longitudinal velocity in the direction normal to the plate. D al a
1) At small Reynolds numbers, the viscous forces are larger than the inertial forces and large enough to suppress the rapid fluctuations of the flow. These flows are called laminar flows. True or False 2) The control volume is selected arbitrary, but the bounding control surface should be fixed. True or False 3) In the following figure, which control volume is the best? a) cannot be determined b) CV B c) CV A = CV B d) CV A
In laminar flow, the growth of the boundary layer thickness δ with distance downstream x is given by where Rex = xUe/ν, ν is the fluid kinematic viscosity, Ue is the freestream velocity, and K is a constant. (a) Given that the velocity profile is described by U/Ue = y/δ, find the growth of the displacement thickness, and the momentum thickness with downstream distance. (b) What is the shape factor H?
A 600-mm diameter non-rigid pipe conveys water from a reservoir with a velocity of 2.50 m/s. The flow is suddenly stopped by the closure of a valve situated 200m from the reservoir. Assume that the pressure increases at a uniform rate and that there is no damping of the pressure wave. The pipe has a thickness of 20mm and a modulus of elasticity of 1.40x1011 Pa. The bulk modulus of elasticity of water is 2.20x10° Pa. Which of the following most nearly gives the celerity of the pressure wave? O 1,108.92 m/s O 1,286.47 m/s O 1,222.76 m/s O 1,483.24 m/s
In a fluid the velocity mea sured at a distance 75 mm from the boundary îs 125 m/s- The fluid has absolute vis co Sity o.048 Pa s and of rejutive density 0.913. What is the velouty gradient and shear Stress qt the boundary assuming a linear velocity distribution ? Determine kinematic viscosity.
Which statement is not correct regarding inviscid regions of flow? (a) Inertial forces are not negligible. (b) Pressure forces are not negligible. (c) Reynolds number is large. (d ) Not valid in boundary layers and wakes. (e) Solid body rotation of a fluid is an example.
Q3. When a fluid flows over a surface, the shear stress 7 (N/m²) at the surface is given by the expression du t = μ₁ dy surface where is the viscosity (Ns/m²), u is the velocity parallel to the surface (m/s), and y is the distance normal to the surface (cm). Measurements of the velocity of an air stream flowing above a surface are made with an LDV (laser Doppler velocimeter). The following values were obtained: y 0.0 1.0 2.0 3.0 0.00 55.56 88.89 100.00 u 4.0 111.56 At the local temperature, µ = 0.00024 Ns/m². Calculate (a) du / dy at the surface based on third order polynomial, (b) the corresponding values of the shear stress at the surface, c) the shear force acting on a flat plate 10 cm long and 5 cm wide.
Q.1A/ Answer both MCQ sub-questions: 1. In the forced vibration, the motion of the spring( which is usually represented by a differential equation) is affected by: • Restoring force • Damping force • External force • All of the above 2. The motion of spring represented by the equation: d2x + 64x = 0 dt2 Can be described as: • Overdamped • Critically damped • Underdamped • None of the above ural
3. Determine the maximum value (Qc)max and the minimum value (Qc)min under the action of moving concentrated loads shown in the figure. 30kN 60kN 4m CI 3m 3m 3m 3m 3m
Mechanics of Deformable Bodies A Solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross-sectional area of 150 mm x 310 mm to the median line of the cross-sectional. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube. If it is subjected to a torque T = 15 kN·m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa thickness of the tube is 10 mm and the torque T= 15 kN·m.
Find the strain if change in length 0.003mm and initial length of rod 1000 mm
When a fluid flows over a surface, the shear stress T (N/m) ) at the surface is given by the expression du dy surface where u is the viscosity (N-s/m ), u is the velocity parallel to the surface (m/s), and y is the distance normal to the surface (cm). Measurements of the velocity of an air stream flowing above a surface are made with an LDV (laser-Doppler-Velocimeter). The values given below were obtained. y y и 0.0 0.00 2.0 88.89 1.0 55.56 3.0 100.00 At the local temperature, u = 0.00024 N-s/m. In four decimal places, calculate du/dy at the surface using all the points. Answer =