Show complete solution and round-off your answers to four decimal places. Calculate the amount of calcium chloride per tablet if the sample powder weighing 0.2382 g required 16.52 mL of 0.1150 M EDTA for titration. The weight of 20 tablets taken was 7.75 g. Answer: _ mg

Show complete solution and round-off your answers to four decimal places. Calculate the amount of calcium chloride per tablet if the sample powder weighing 0.2382 g required 16.52 mL of 0.1150 M EDTA for titration. The weight of 20 tablets taken was 7.75 g. Answer: _ mg

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter5: Errors In Chemical Analyses

Section: Chapter Questions

Problem 5.10QAP

See similar textbooks

Related questions

Q: In running a Beer’s Law lab, you are given 50.00 mL of a 25.00 µM solution of the organic pigment…

A: The initial concentration of crystal violet is 25.00 µM and volume of this solution is 50.00 mL…

Q: 2.1 Calculate the pH of 1.0 M HC2H3O2 solution, using Ka = 1.7 × 10-5 . Begin this calculation by…

A: #Q.2.1: Given the concentration of HC2H3O2 solution = 1.0 M Equation for the dissociation of…

Q: Experiment 1: Determination of the solubility of potassium bitartrate in water. NaOH concentration…

A: Bitartarate ion (HC4H4O6-) is a monoprotic acid, and NaOH(aq) is a monoacidic base. Hence they…

Q: On their second titration trial, the CHM 111 student recorded an Initial titrant volume of 9.95 mL…

A: Given : Initial titrant volume = 9.95 mL And final titrant volume = 29.80 mL

Q: The labware we used in Quant Lab is divided into “qualitative” or “quantitative” analytical purpose.…

A: Labware for qualitative and quantitative analysis.

Q: please answer questions 1) and 2) (they are part of the same question). thank you

A: The term number of moles is defined as the ratio of mass to the molar mass of the given compound.…

Q: In the titration of 25.00 mL of a water sample, it took 19.040 mL of 4.965x 10−3 M EDTA solution to…

A: EDTA is used to measure the hardness of water Water hardness is primarily due to calcium and…

Q: Starting with 2.0 g of hand sanitizer in 10 mL of methanol (density of methanol = 0.791 g/mL), the…

A: Given that

Q: Show calculations and briefly describe how you will make the following solutions: 50.00 mL of 0.200…

Q: Add the following to 400ml H2O (not from the tap!) 5.4 g Tris base 50.0ml 10X Boric acid (55.0…

A: A question based on concentration terms that is to be accomplished.

Q: 1. Remember that all solutions used in this experiment contain 0.50 M HNO;. What happens to the HNO3…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Lab Data Standardized NaOH (M) 0.4102 Initial volume of buret (mL) 0.90 Volume of vinegar (mL) 10.00…

Q: A colored solution of concentration 0.0248 mol/L has an absorbance of 0.353. What is the…

A: The Beer-Lambert’s law, the absorbance (A) is directly proportional to the concentration (c) of the…

Q: A student performed a titration to determine the exact concentration of NaOH(aq). The titration was…

A: Average titre value = 25.06 + 25.15 + 25.02 + 25.17 + 25.075 = 25.09

Q: Write the mass balance and charge balance equation of 0.20 HNO2. Note that HNO2 is a weak acid

A: Solution Given that Equation of = 0.20 HNO2 Weak acid is = HNO2…

Q: To determine the percent purity of a sample containing iron(II) ammonium sulfate; Suggest , 2…

A: The question is based on the concept of quantitative analysis. we have to quantitatively estimate…

Q: Calculate equivalent weight of unknown acid using the following information: Mass of unknown acid=…

A: Given,Mass of an unknown acid = 0.1351 gVolume of NaOH used to titrate the acid = 11.5…

Q: D-3: Zinc + Copper Sulfate 53. Observations on combining Mg metal and 0.1 M CuSO4 solution Balanced…

Q: To determine the amount of copper and the identity of the copper compound in the unknown sample, a…

A: Given that - Initial volume of the copper sample Solution = 100 mL Mass of copper sample = 120.8 mg…

Q: mass of KIO3 = 0.9290g titrated volume Na2S2O3 = 28.88mL standardisation sodium thiosulfate

Q: An impure sample containing 2.00 g of sodium carbonate and bicarbonate was taken. It was dissolved…

A: The question is based on the concept of mix indicator titration. At phenolphthalein end point, Only…

Q: Exactly 1.00 grams of granular table salt was dissolved in deionized water up to 500 mL. An aliquot…

Q: Answer the following: Maria was given a capsule of multivitamins and she was asked to determine the…

A: Given as The weight of Ascorbic acid is 1.032 g. We have to determine the % by mass (w/w) of…

Q: 2.5 ml of an unknown dye having a molarity of 3.6 x 10° M is diluted to a final volume of 20.0 ml.…

A: This is a dilution problem of mole concept. On dilution , the concentration of a substance…

Q: The following steps were used to determine the concentration of acetic acid in vinegar. 1. Sodium…

Q: 10 CCh and diluting to 150.0 mL. a Calculate moles of Na", Ca³" and Cl- in the solution b. Using…

A: a.) To calculate moles of each ion, we would first Calculate moles of NaCl and CaCl2 solution . Then…

Q: Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Ni(NO3)2 From the stock…

A: The dissolution of a solid substance in a solvent provides the solution. The presence of a specified…

Q: A student determined the concentration of copper by ion exchange. He obtained the following results:…

Q: Direction. Write your answer on a separate sheet of paper. For items involving calculation show your…

Q: A student followed the procedure of this experiment to determine the percent NaOCI in a commercial…

A: “Since you have posted a question with multiple sub-parts, we will solve first Four sub-parts for…

Q: Mass of zinc = 1.050 g. Calculate the number of moles of zinc in the 250 mL flask (show workings)…

A: There are multiple questions asked in a single question, so as per our guidelines, I will answer…

Q: A formula calls for 0.6 mL of a coloring solution. Using a 10 mL graduated calibrated from 2 to 10…

A: Step : 1 obtain the desired quantity of the coloring solution by the aliquot method.

Q: 10. Engr. Yebes and Engr Quadra were tasked with preparing two solutions for an experiment. Engr.…

A: Two solutions were prepared- Engr. Yebes prepared one with a non-volatile, non-electrolyte solute.…

Q: * OWLV2 | Online teachinX C The Deep Blue Compound (+…

A: Concentration of the solution (solution 2) obtained on diluting 0.164 M HCl can be determined as…

Q: If you have a sample of 42.6 mg/L of calcium and 7.2 mg/L of magnesium, what concentration does the…

A: A numerical problem based on complexometric analysis, which is to be accomplished.

Q: Assuming

A: Extinction co-efficient = 0.01662 Lmg-1cm-1 Concentration of unknown sample = 14.634g/ Explanation~

Q: Multiple Choice Each of the numbered items or incomplete statements is followed by answers or by…

A: Dear student, since the given question is a multiple question, hence I solved first question…

Q: Express each of the following concentrations as a ratio strength: (a) 2 mg of active ingredient in…

Q: Andrew dissolved 10.00 grams of an iron ore sample in 5.00 L of acid to produce a stock solution.…

A: The diluted solution was found to be containing 1.62×10-5 M Fe2+.

Q: SLO-MO calculations Suppose 125 ml of the basic analetes at union Concentration: 185 M € ume 450 mL…

Q: the titrant was consumed in each run? Trial 1: 0.009981 M Trial 2: 0.009862 M Trial 3: 0.01029 M

Q: Identify and explain the mistakes made in the following laboratory protocols: A 1250 mg sample of…

A: Before measuring the mass of any chemical compound, it is quite necessary to adjust the balance to…

Q: How many milliliters of 0.05 M EDTA are required to react with the calcium and magnesium in a 0.1414…

Q: A student needs 25.0 mL of 7.18x10 4 M FD&C Blue Dye No. 2 solution. If the student has 2.00 mM FD&C…

A: We will solve this question using molarity equation.

Q: Answer the following questions and show all calculations: a. Explain what a dilution factor is, in…

A: When stock solution is added to diluent then concentration of stock solution also decreases, this is…

Q: QUESTION NO. 1: A 0.097 N silver nitrate solution of 56.3 ml was used to titrate two samples of…

A: Solution stoichiometry is mainly based on the calculation of moles and volumes. These two values are…

Q: Calculate equivalent weight of unknown acid using the following information: Mass of unknown acid=…

Q: QUESTION NO. 2: A 0.385 g sample of sodium chloride was assayed by the Volhard method using 50 ml of…

A: Percent of compound in sample: It is defined as the amount of compound determined divided by the…

Q: Please help me out with making flowchart with thes steps. Write the result. Procedure 1.…

A: The flow chart for the given steps is shown below

Q: 25.00 mL of 0.041 32 M Hg2(NO3)2 were titrated with 0.057 89 M KIO3. Hg₂+ + 2103 →→ Hg₂(103)2(S)…

Question

Show complete solution and round-off your answers to four decimal places.

Calculate the amount of calcium chloride per tablet if the sample powder weighing 0.2382 g required 16.52 mL of 0.1150 M EDTA for titration. The weight of 20 tablets taken was 7.75 g.

Answer: _ mg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Distinguish between the terms slightly soluble and weak. electrolyte.
The grid has six lettered boxes, each of which contains an item that may be used to answer the questions that follow. Items may be used more than once and there may be more than one correct item in response to a question. Place the letter(s) of the correct selection(s) on the appropriate line. Could dissolve Zn(OH)2 _____________ Could be used to prepare a buffer from __________ Halfway to the equivalence point in the titration of a weak, monoprotic acid with strong base ________ SO2-related atmospheric phenomenon __________ Species formed by a Lewis acid-base reaction ________ General condition required for precipitation to occur ________ [conj. base] = [conj. acid] in a buffer ___________
A solution of HCl was titrated against sodium carbonate. What is the normality of acid for Trial 3 in the given data? T1 T2 0.3562 0.3479 0.3042 Weight (g) Initial V (mL) 0.80 1.60 0.40 Final V (mL) 35.20 36.70 39.80 Vol HCI used (ml) 35.10 39.40 N of HC (eq/L) 0.1954 0.1870 Average N of HCl (eq/L)
1. A sample of pure sodium oxalate, Na2C2O4 , weighing 0.2856 g is dissolved in water, sulfuric acid is added, and the solution titrated at 70°C , requiring 45.12 mL of a KMNO4 solution. The end point is overrun and back-titration is carried out with 1.74 mL of a 0.1032 N solution of oxalic acid. Calculate the normality of the KMNO4 solution. Hint: A redox reaction is involed between oxalate and permanganate. Look at the changes in oxidation state by determining the balanced redox reaction: 5C20,2 + + 2MN2+ 2 Mn04 + 10H* → 10CO2 + 8H20
18.9 milliliters of a 1.687 M KOH solution are required to titrate 30.1 milliliters of a H3PO4 solution. What is the molarity of the H3PO4 solution? ЗКОН + HзРОД --> K3PO4 + 3H2O Please put answer in box with 3 digits past decimal in regular non scientific notation.
A 5.00 mL wine vinegar was diluted to 25 mL and was titrated with 0.1198 M NaOH to determine its acidity. The endpoint was reached after addition of 31.45 mL of the NaOH solution. Calculate the % acidity of sample expressed as % acetic acid (w/w) if the density of the wine vinegar is 1.105 g/mL.
A student determined the concentration of copper by ion exchange. He obtained the following results: (4.2180x10^1) mL of (9.64x10^-2) M NaOH solution was required to titrate the eluate (HCI solution) from the column. He used a 15.0 mL sample of copper chloride solution initially. Calculate the concentration of Cu*2 in the original solution. Your answer should be in correct scientific notation (that is what the red text in BrightSpace means.) Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: |x10 Answer
Other information not on photo 2 gram potassium bitartrate are put into a 250ml flask. 150ml water is added. The solution is stirred and left to settle. the solution if filtered through a dry funnel into a 250ml breaker. 25ml of this solution was placed into 4 different flasks each. Approximately 11.5666667ml of NaOH was added to each flask. What is the concentration of the HC4H4O6-? (Asked on the right side of the table)
On their second titration trial, the CHM 111 student recorded an Initial titrant volume of 9.95 mL and a Final titrant volume of 29.80 mL. Using the correct number of significant figures, what volume of titrant was used?
Titration of Acetic Acid CH3COOH 1) Record the exact Molarity of the freshly prepared solution of NaOH by reading the label on the bottle, include all digits provided. This is the solution that will be in the buret. MB 0.0500 M 2) Record the exact volume of acid CH,COOH that was pipetted into the Erlenmeyer 10.00 aak mL. Note the concentration is unknown and what you will solve for. (This was diluted with 50 mL of water in the Erlenmeyer flask) Trial 1 Trial 2 Trial 3 Final base (mL) 30.46 30.98 29.88 Initial basc (mL) 0.45 0.05 0.04 Total base (mL) *Molarity (M) HOOD HO "Use atoichiometry to determine the molarity of your CIHCOOH solution fromn each of trial. Show all work Including units for one. Caleulate Average Molarity
You want to determine the concentration of NaCl in a water. In preliminary analysis, it appears to be saline water with a NaCl content of approximately 4%. Should you dilute the sample if your titrant has a concentration of 0.1 M and you want to spend 25 mL of sample? Solution: You must dilute approximately ten times, taking 10 mL of sample and making up to 100 mL. In this way, 17.20 mL of titrant will be spent.
You have prepared 1.000 M of NaOH solution. To determine the accuracy of the solution you prepared you have carried out two titration trials. Calculate the actual concentration of NaOH solution you prepared for each titration trials, and the average concentration. All your final answers should be reported to 4 significant figures. Trial 1: Weight of KHP = 5.0320 g MW(KHP) = 204.2 g/mole NaOH titrant volume = 24.40 ml 2. Trial 2: Weight of KHP = 5.0123 g MW(KHP) = 204.2 g/mole NaOH titrant volume = 24.34 ml Calculate the average concentration of Trial 1 and 2.