Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 24 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 115 Fo. Use the following dimensions and properties: a = 3.5 ft, b = 7.5 ft. Rod (1): d 1= 1.10 in.,L 1= 12 ft , E 1= 15,200 ksi , a 1= 12.20 × 10 - 6 /Fo. Rod (2): d 2 = 0.65 in. , L 2 = 10 ft , E 2 = 28,000 ksi, a 2 = 9.60 x 10 - 6/Fo. Rod (3): d 3 = 1.15 in. , L 3 = 6 ft, E3 = 15,200 ksi , a 3 = 12.20 x 10 - 6/Fo. (1) L (2) b L2 a Rigid bar A (3) L3 P vD = i in.

Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 24 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 115 Fo. Use the following dimensions and properties: a = 3.5 ft, b = 7.5 ft. Rod (1): d 1= 1.10 in.,L 1= 12 ft , E 1= 15,200 ksi , a 1= 12.20 × 10 - 6 /Fo. Rod (2): d 2 = 0.65 in. , L 2 = 10 ft , E 2 = 28,000 ksi, a 2 = 9.60 x 10 - 6/Fo. Rod (3): d 3 = 1.15 in. , L 3 = 6 ft, E3 = 15,200 ksi , a 3 = 12.20 x 10 - 6/Fo. (1) L (2) b L2 a Rigid bar A (3) L3 P vD = i in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

EXAMPLE 4.2 The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm²; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm?. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. %3D 0.4 m 0.3 m 30 kN D E -0.4 m 0.2 m
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A concentrated load of P = 17 kips is applied to the free end of bronze rod (3). Determine the magnitude of the deflection of rod end D after the temperature of all rods has increased by 105°F. Use the following dimensions and properties: a = 3.0 ft, b = 5.5 ft. Rod (1): di = 0.90 in., L1 13 ft, Ej = 15,200 ksi, a1 12.20 x 10-6"F. Rod (2): d2 = 0.70 in., L2 10 ft, E2 = 28,000 ksi, a2 = 9.60 x 10-6"F. Rod (3): d3 1.20 in., L3 = 6 ft, E3 = 15,200 ksi, a= 12.20 × 10-6ľF. |(1) (2) b |L2 a Rigid bar A |(3) L3 D
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 512 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 643 mm2. For the 32 kN force shown, determine the deflection of D (mm) *Note: Negative if compression and positive if tension. Also, the final answer should have two decimal places.
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is applied to the end B of the shaft. Determine the rotation of section B. The shaft and beam are made of an aluminium alloy for which E= 720 GPa and G = 27 GPa, Neglect the strain energy of the hub DF. IC 400 mm 200 mm- 40.0 mm D 60.0 mm 400 mm 800 mm HO H 30.0 mm T= 2.00 kN.m
A loaded beam is shown in figure. EI B Rigid L 2 M M AB is flexible and 'BC' is rigid. Maximum deflection is
The beam shown in the Fig.is 7m long with EI = 200MNm^2 Let P = 10 kN Determine the following: a. Reaction at A.b. Constant.c. Slope at 2m from A.d. Deflection at 2m from A.
= 29,000 For the structure and loading shown below, find the lateral deflection at the top. Use E ksi and I = 250 in4 for all members. Note that in frames, we neglect axial deformation, so you can calculate the deflection at either of the upper corners; the answer will be the same. t. 201 8K 10! 1. What is the deflection at the top in inches (two decimal places) ot
Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. 0.4 m 0.5 m B P 20-mm diameter 60-mm diameter 2. What is the value of Q in kN so that the deflection at A is zero if P = 59 kN?
As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 320mm² and link (2) has a cross-sectional area of 480mm². For an applied load of P= 58kN, determine the rigid beam deflection at point B. (2) 4,000 mm (1) 2,500 mm B 1,400 mm 800 mm