Review Question 2. Consider a reheat-regenerative vapor power cycle with two feedwater heaters, a closed feedwater heater and an open feedwater heater. Steam enters the first turbine at 8.0 MPa, 480C and expands to 1.0 MPa. The steam is reheated to 440C before entering the second turbine, where it expands to the condenser pressure of 0.008 MPa. Steam is extracted from the first turbine at 2 MPa and fed to the closed feedwater heater. Feedwater leaves the closed heater at 210 C and 8.0 MPa, and condensate exits as saturated liquid at 2 MPa. The condensate is trapped into the open feedwater heater. Steam extracted from the second turbine at 0.5 MPa is also fed into the open feedwater heater, which operates at 0.5 MPa. The stream exiting the open feedwater heater is saturated liquid at 0.5 MPa. The net power output of the cycle is 150 MW. There is no stray heat transfer from any component to its surroundings. If the working fluid experiences no irreversibility as it passes through the turbines, pumps, steam generator, reheater, and condenser, determine (a) the thermal efficiency, (b) the mass flow rate of the steam entering the first turbine, in kg/s. (c) Heat rejected in the condenser, kW

Review Question 2. Consider a reheat-regenerative vapor power cycle with two feedwater heaters, a closed feedwater heater and an open feedwater heater. Steam enters the first turbine at 8.0 MPa, 480C and expands to 1.0 MPa. The steam is reheated to 440C before entering the second turbine, where it expands to the condenser pressure of 0.008 MPa. Steam is extracted from the first turbine at 2 MPa and fed to the closed feedwater heater. Feedwater leaves the closed heater at 210 C and 8.0 MPa, and condensate exits as saturated liquid at 2 MPa. The condensate is trapped into the open feedwater heater. Steam extracted from the second turbine at 0.5 MPa is also fed into the open feedwater heater, which operates at 0.5 MPa. The stream exiting the open feedwater heater is saturated liquid at 0.5 MPa. The net power output of the cycle is 150 MW. There is no stray heat transfer from any component to its surroundings. If the working fluid experiences no irreversibility as it passes through the turbines, pumps, steam generator, reheater, and condenser, determine (a) the thermal efficiency, (b) the mass flow rate of the steam entering the first turbine, in kg/s. (c) Heat rejected in the condenser, kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 5. Calculate the thermal efficiency of the cycle
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 4. Calculate the total turbine work of the cycle.
In an ideal Rankine cycle the boiler pressure is 10 MPa. All components are operating at steady state and adiabatically. The steam enters the turbine at 550oC. The condenser pressure is 15 kPa. Determine the cycle efficiency.Find the entropy generation for the condenser for 6 kg/min mass flow rate of steam. This is a Thermodynamics question. Please explain all steps and write nicely. Thanks.
An ideal regenerative cycle is executed with steam generation at 10 MPa and 600 deg C. Before condensation at 0.005 MPa, steam is extracted for feedwater heating first at 2.5 MPa and second at 0.6 MPa. On the basis of 1 kg of throttle steam, find: a. m1 and m2 in kg/kg b. ec in percent c. ee in percent Reminder: 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places.
1.) A steam power plant uses the ideal Reheat Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then it is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate kg 3241.70,2144.67,1101.06 4.03, 1097.03 33.84%, 3.28 k kJ kg kl, kg kWh
1.Solve the Rankine Regenerative Cycle problem below. 2. Draw a detailed Schematic and Ts Diagram. 3. Show and follow step by step procedure of solution A steam power plant based on ideal regenerative cycle. Steam enters the turbine at 400oC and 3MPa state while the condenser pressure is 10 kPa. Find the cycle efficiency and mass fraction of steam extracted at 0.6MPa for an open type feedwater heater
An ideal regenerative cycle is executed with steam generation at 10 MPa and 600 deg C. Before condensation at 0.005 MPa, steam is extracted for feedwater heating first at 2.5 MPa and second at 0.6 MPa. On the basis of 1 kg of throttle steam, find: a. m1 and m2 in kg/kg b. ec in percent c. ee in percent Reminder: 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. please use this steam table https://drive.google.com/drive/folders/1jGaspdm5O-DfZylEuR2bnxBshJQrq0Ww?usp=sharing
An ideal regenerative cycle is executed with steam generation at 10 MPa and 600 deg C. Before condensation at 0.005 MPa, steam is extracted for feedwater heating first at 2.5 MPa and second at 0.6 MPa. On the basis of 1 kg of throttle steam, find:a. m1 and m2 in kg/kgb. ec in percentc. ee in percent Reminder:1. For values taken from the steam tables: Use them as is, do not round off.2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places.PLEASE USE THIS STEAM TABLE:https://docs.google.com/document/d/1wUPYkDmHnCMBEuLRMRTGEfz4D5kkohT4/edit
Problem (1.2) A steam power plant working according to simple Rankine cycle. It has a high pressure of 3 MPa and it maintains 60°C in the condenser. A condensing turbine is used, but the quality should not be lower than 90% at any state in the turbine. Find the cycle efficiency. [reference: Fundamentals of Thermodynamics by Borgnakke & Sonntag prob.11.18,p-460].(Ans.33.2 %).
USE THE GIVEN BELOW.In a simple Rankine cycle, the steam throttled condition is 8 MPa and 480°C. The steam is then reheated to 2 MPa and 460 °C. If turbine exhaust is 60 °C, determine the following: a. Heat Added b. Turbine Work c. Heat Rejected d. Pump Work e. Net Work f.EfEfficiency
2.) A steam power plant uses the ideal Regenerative Rankine cycle with single open feedwater heater where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then some steam is extracted at this point. The remaining steam expands and enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work. kJ kg 20.01%, 2286.801457.51,832.54 3.34,829.2936.26%, 4.34. ) kg kWh
2.6). A gas-turbine plant operates on the regenerative Brayton cycle with two stages of reheating and two stages of intercooling between the pressure limits of 100 and 1200 kPa. The working fluid is air. The air enters the first and the Regenerator second stages of the compressor at 300 K and 350 K, respectively, and the first and Reheater the second stages of the turbine at Comb. cham. 1400 K and 1300 K, respectively. 6 Wnet Assuming both the compressor and the Comp. I Comp. II Turb. I Turb. II turbine have an isentropic efficiency of 80% and the regenerator has an effectiveness of 75%, determine (a) the Fig. p2.6. Intercooler back-work ratio and the network output, For two-stage compression and expansion, the work input is minimized and the work output is maximized when both stages of the compressor and the turbine have the same pressure ratio. and (b) the thermal efficiency. 2.7). A simple gas turbine, has the following data: Compressor pressure ratio, p = 20 Turbine inlet…