Q4/ Figure show an epicyclic gear train. Gear A has 20 teeth, gear Bhas 22 teeth, and gear C has 15 teeth. Gear B and C is acompound gear. If gear E is fixed and gear A rotates at 1000 rpm,find the speed of arm and number of teeth for gear E.BA

To solve this problem involving an epicyclic gear train, we need to use the fundamental equations…

Answered: Q4/ Figure show an epicyclic gear…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An epicyclic gear train as shown in figure. Gear D has 65 teeth, gear C has 15 teeth and annular gear A has 120 teeth. Gears B and C are compound. If the annual gear A is fixed and gear D rotate 600 rpm, find the speed of arm. A B- D -C
An indexing mechanism of the milling machine uses a gear train shown in figure task 1d. The drive is from gear wheels A and B to the bevel gear wheel D. The following table shows the tooth number on each gear, solve using tabular method. How many revolutions does D makes for one revolution of A under the following situations: Tabular column (i) If A and B are having the same speed and same direction (ii) If A and B are having the same speed and opposite direction (iii) If A is making 80 rpm and B is at rest (iv) If A is making 80 rpm and B 40 rpm in the same direction. (v) Also define the term Speed ratio and train value
As shown in the figure a planetary gear train consist of the arm C coupled to two gears A and B with 40 and 60 teeth respectively. If the arm rotates at 150 rpm in the anticlockwise direction about the center of the fixed gear A. Calculate the speed of gear B. How fast will gear B move if the gear A makes 300 rpm in the clockwise direction instead of being fixed. (must use Tabular method) B Arm C C A B Nber of teeth Total rotations
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
An epicyclic gear train as shown in figure the number of teeth on gear A,B,C are 48,24,50 respectively. If the arm rotates with (340) rpm in clockwise find 1. Speed of C when A is fixed 2. Speed of A when C is fixed
In a compound epicyclic gear train, has gears A and an annular gears D & E free to rotate on the axis P. B and C is a compound gear rotate about axis Q. Gear A rotates at 75CCW rpm CCW and gear D rotates at 390CW rpm CW. Find the speed and direction of rotation of arm F and gear E. Gears A, B and C are having 16, 45 and 21 teeth respectively. All gears having same module and pitch. Sketch the arrangement and solve by tabular column method.
A bicycle's gear ratio is the number of times the freewheel turns for every one turn of the chainwheel (see figure). The back half of a bicycle is given. A line labeled "Freewheel" is pointing at the center of the rear wheel. A line labeled "Chainwheel" is pointing to the center piece connecting the two pedals. The table shows the numbers of teeth in the freewheel and the chainwheel for the first five gears of an 18-speed touring bicycle. The chainwheel completes one rotation for each gear. GearNumber Number ofTeeth inFreewheel Number ofTeeth inChainwheel 1 32 24 2 26 24 3 22 24 4 32 40 5 19 24 Find the angle through which the freewheel turns for each gear. Give your answers in both degrees and radians. (Round your answers to one decimal place.) gear 1 = rad= gear 2= ° rad= gear 3= ° rad= gear 4= ° rad= gear 5= ° rad=
The Diameters of pulleys of belt drive and number of teeth on the gears 2 to 7 are indicated in the figure. Find the speed and direction of rotation of gear 7?
In a spur gear arrangement, the driver has 80 teeth of 39 mm pitch. Find the power, if it can transmit a tangential force of 60 N. Take speed of driver as 150 rev/min. Insert your answer for power in watt correct up to at least a third decimal place.
In the epicyclic gear train shown in the given figure, P is fixed. P has 120 teeth and Q has 30 teeth. If the arm R makes three revolutions, the number of revolution made by Q will be R
Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly at 100 RPM. Minimum number of teeth can not be less than 20 and the maximum numbor of teeth can not be more than 150. The speed of goar B must be exactly 500 RPM. Determine tho speed of gear C: Note: This is a short answer type question with limited space for answer. Therefore, write the answors and do not show any other details. Input pinion A N= 20 teeth W,= 1,500 rpm No B
consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number of teeth on gear planeta (3) is Z3 = 20 and the number of gear anel (4) Z4 = 70 the speed of gear sol, w2 = 300 rpm and of anel w4 = 200 rpm find the speeds of gear sol and braço carregador b

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q4/ Figure show an epicyclic gear train. Gear A has 20 teeth, gear B has 22 teeth, and gear C has 15 teeth. Gear B and C is a compound gear. If gear E is fixed and gear A rotates at 1000 rpm, find the speed of arm and number of teeth for gear E. B A