Q2 : Design the simply supported reinforced concrete beam showing in the Figure below for bending moment using Ultimate Strength Design Method, for the following data: f'=20 MPa, f-300 MPa, density of concrete =24 KN/m (use Ø22 for main reinforcement and Ø10 for shear reinforcement). PD=3kN Pp=3kN W Self- WD-12KN-m WL=6 KN/m 2m 3m 2m

Q2 : Design the simply supported reinforced concrete beam showing in the Figure below for bending moment using Ultimate Strength Design Method, for the following data: f'=20 MPa, f-300 MPa, density of concrete =24 KN/m (use Ø22 for main reinforcement and Ø10 for shear reinforcement). PD=3kN Pp=3kN W Self- WD-12KN-m WL=6 KN/m 2m 3m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure 2 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform service (unfactored) live load of 1.5 kips/ft. The concrete strength is 3500 psi, and the yield strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load (Table 5.3.1) and strength reduction factors from AC1318-14. For the midspan section shown in Fig. P4-1b, compute Mn and show that it exceeds Mu. @ (b) 3 No. 9 bars WD = 1.4 kips/ft plus weight of beam 1.5 kips/ft WL H 12 in. 20 ft TT 21.5 in. 24 in. + Figure 2.
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced with a single high strength steel bar that has a cross- sectional area of 0.42 in2.The bar has a normal tensile strength of 145 ksi, linear stress-strain curve to failure, and a strain at failure of 1.8 percent. The concrete strength fc= 6000 psi. Calculate the nominal flexural strength of the section.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places.
O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'
Please double check your final answer. Subject - reinforced concrete A simply supported rectangular beam has a width of 300mm and the distance to the centroid of tension reinforcement is 330mm. The tension reinforcement has an area of 2463mm.2 and the area of compression reinforcement placed 70mm from the compression face of the beam is 1231.5mm.2, fy = 415MPa, fc'=30MPa, balanced steel ratio of 0.031.The design strength using 0.90 as the reduction faction is Choices A. 282kN.m B. 245kN.m C. 254kN.m D. 228kN.m
Using the stress block, determine the ultimate moment of resistance of the section shown in Figure 2 and check whether the steei provided satisfies the bending moment due to the loads on the beam. Characteristic compressive strength of concrete, fck= 25 N/mm² Characteristic tensile strength of steel, fyk = 500 N/mm2 Clear cover to main steel as 20 mm. Ultimate Design Load =13 kN/m 2 402 mm 370 mm 2 1470 mm 9 m 230 mm Figure 2
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
PROBLEM: A rectangular reinforced concrete beam has a width of 310 mm and an effective depth of 490 mm. Concrete compressive strength (fc') is 21 MPa, and steel yield strength (fy) is 345 MPa. Use USD Method. DETERMINE: 4. Ultimate moment capacity if the beam is reinforced with 8 – 25 mm diameter tension steel. 5. Ultimate moment capacity if the beam is reinforced with 10 – 25 mm diameter tension steel.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 2.6 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 ▾of 1 10 ft a P B9 in. 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μA Pmax= 158.91 kips Submit My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue