Problems 1 Generate the following sequences using the basic MATLAB signal functions and the basic MATLAB signal operations discussed in this chapter. Plot signal samples using the stem function. 2. x₂ (n) = = Σ -5e-1k|8(n − 2k), −10 ≤ n ≤ 10. - 8. x8 (n) = e0.01n sin(0.1πn), 0≤ n ≤ 100. Comment on the waveform shape. By Younis M. Jalil

Problems 1 Generate the following sequences using the basic MATLAB signal functions and the basic MATLAB signal operations discussed in this chapter. Plot signal samples using the stem function. 2. x₂ (n) = = Σ -5e-1k|8(n − 2k), −10 ≤ n ≤ 10. - 8. x8 (n) = e0.01n sin(0.1πn), 0≤ n ≤ 100. Comment on the waveform shape. By Younis M. Jalil

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) How you will convert sin function to cosine? List trigonometric any three properties associated with these functions. 2) Briefly describe application of impulse function and impulse train. 3) How you relate phase shift and time shift of a signal? 4) List the few important Matlab function names to simulate various waveforms.
Nowadays switching power supplies are commonly used because they offer better efficiency and smaller size compared to a linear power supply, because high switching frequency allows for smaller transformers. One place to find a SMPS (switching mode power supply) is a phone charger. Switching power supplies cause high frequency noise on switching transients. The noise on the output is filtered in various ways but savings may be considered on the output filter (extra inductors and capacitors = extra costs), which means the output will have some amount of noise left getting to the device via the USB cable. Estimate the frequency where the phone charger starts to act as an antenna when the USB cable length is 1.9 meters. Submit your answer in MHz without the unit, rounded to one decimal place. Hint: Either "rule of thumb" can be used.
Given the continuous-time, continuous-amplitude signal waveform x(1) -3 sample at discrete values of time and plot the discrete-time signal x[n]. Also, extract the even and odd parts of x[n]. Please show the complete and detailed solution. Thank you
Equation Q4 shows a sinusoidal message signal, v(t). v(t) = 2 cos(10000nt) + 5 cos(2 + 20000nt).Equation Q4 A Pulse Code Modulation (PCM) technique which uses a uniform quantizer is applied in converting the v(t) to a binary signal. The signal is sampled at a rate of 15% above the Nyquist for practical reasons and the samples are quantized into 65,536 levels. Based on the digital technique used, a) compute the minimum bandwidth required to encode and transmit the signal b) compute the amount of bandwidth increase in percentage after the information signal has been digitized. c) compute signal-to-quantization noise ratio at the output of the quantizer if the quantization levels given in Q4(a) have been quartered, compute the new signal-to-quantization noise ratio at the output of the quantizer d)
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
i. Briefly discuss the three types of responses in a series RLC circuit. Write down the conditions for the three responses in terms of the neper frequency, a, and undamped natural frequency (or resonant frequency), wo. ii. A series RLC circuit is connected to a voltage source that steps from 0V to 5V at t = 0s. The values ofL and C are 100mH and 0.1uF respectively, while R ranges from 200 Q to 5 k Q. Assume zero initial conditions. a. Write down the expression of the voltage across the capacitor for the three types of responses (for the three different values of R).
Ex. 600. A series circuit containing a resitor (6 Ohms), a capacitor (4 Farads), inductor (13 Henries), and a voltage source V. Determine the transfer function I(s)/V(s) and then determine the undamped natural frequency (Wn) and damping ratio (zeta). Answers: Wn, and zeta. ans:2
50. A signal x(t) = = sinc (150nt) is sampled at a rate of a) 100 Hz, b) 200 Hz, and c) 300Hz. For each of these cases, explain if you can recover the signal x(t) from the sampled signal.
The number of branches of the root locus indicates The shape of the input test waveform The number of closed-loop poles The gain of the system Whether or not the Routh-Hurwitz criterion can be applied to the O response
From the figure, a Obtain the transfer function Eo(s)/Ei(s). b Sketch the response of eo(t) due to a step change in ei(t) of 2 V. Hint: arbitrarily pick values for L, C, R1, R2 Solve it by loop and give right answer
This is a practice question from my Introduction to Circuits course. I am having a hard time finding the poles for this. When I implement the circuit in LT Spice, I can see that the cutoff frequency is somewhere around 16kHz, but I can't figure out how to come up with that value mathematically. It is underdamped; so, will have imaginary components, but I'm lost as to how to find them or what to do with them or how to come up with the correct cutoff frequency to match LT Spice. Thank you for your assistance.
Write short notes on magnitude comparator.