AMotor PulleyscrateMODProblem Statement:One cable runs from a winch motor M, around pulley D, to the ceiling. A second cable runs from the axis of pulley D, around pulleys C, B, and A, to the ceiling. A crate is suspended from the axes of pulleys Aand C. The motor winds up its cable at a rate of 50.3 m/s. Assuming the crate stays level, determine:The speed of the crate after 10 seconds: 1.247 m/sThe time required for the crate to travel 6.1 meters: 4.918 sBe sure to include units with your answers.

Answered: Image /qna-images/answer/269530aa-17c4-438d-98d1-ea7b79fef49e.jpg

Problem Statement: One cable runs from a winch motor M, around pulley D, to the ceiling. A and C. The motor winds up its cable at a rate of 540.3 m/s. Assuming the The speed of the crate after 10 seconds: 1.247 m/s The time required for the crate to travel 6.1 meters: 4.918 s Be sure to include units with your answers.

Problem Statement: One cable runs from a winch motor M, around pulley D, to the ceiling. A and C. The motor winds up its cable at a rate of 540.3 m/s. Assuming the The speed of the crate after 10 seconds: 1.247 m/s The time required for the crate to travel 6.1 meters: 4.918 s Be sure to include units with your answers.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1–2. Figure C1.2 shows a mechanism that is typical in the tank of a water closet. Note that flapper C is hollow and filled with trapped air. Carefully examine the configuration of the components in the mechanism. Then answer the following leading questions to gain insight into the operation of the mechanism. 1. As the handle A is rotated counterclockwise, what is the motion of flapper C? 2. When flapper C is raised, what effect is seen? 3. When flapper C is lifted, it tends to remain in an upward position for a period of time. What causes this tendency to keep the flapper lifted? 4. When will this tendency (to keep flapper C lifted) cease Plz connect me if you want to explan subject for me .... +962 79180149 Thx
Car engine mechanism is the inversions of| kinematic chain.
P4) What is the block diagram of the pneumatic control valva schematic diagram as shown in fig.p4? fig. p4 farm Jupi Po
3.) Assuming that the resistance distance for the total system is just the vertical displacement of the block dR, and the input distance for the total system is the distance the team of horses must pull (d; (rotAL), a. How far must the horses pull (di (rOtAL) in order to raise the block the required 5 meters? b. How much work is done by the horses?
Drop-load (IV) Context We want to lower a suspended load in a controlled way, so that it hits the ground with a speed whose modulus is not too great. To do this, the suspended load (B) is connected by a rope passing through a pulley to another mass (A), which can move on an inclined plane. A spring is attached to mass A to slow down the motion. Information The masses of the charges A and B are known.The pulley is a disc (a solid cylinder) of mass mp and radius R that can rotate without friction.The angle delta of the inclined plane is known.There is friction between mass A and the surface it sits on, the coefficient of friction is uc.The string attached to mass A is parallel to the inclined plane.The spring is parallel to the inclined plane, initially unstretched and its spring constant is known. Modelization Create a model for the modulus of the velocity of mass B when it hits the ground, given the known parameters of the problem that are relevant. Mass of charge A : 80 kg Mass of…
Draw and discuss the FBD for the following system. • Label all forces and directions. • How many unknowns are there? (Remember, an unknown does not have to be a force. It can also be a dimension, angle, etc.) • How many equilibrium equations can you create? • Is there enough information to polve for the unknowns? Explain. C Draw ring A as your particle. 2 m m = 12 kg KAB = 300 N/m
A mechanism is composed of the following: Link 1 (AF) - horizontal ground with a length of 7 cm. "A" is on the left side Link 2 (AB) - 2 cm in length. Initially 30 degrees above the x-axis Link 3 (BCD) - tertiary link, BC=DC=2cm, BD=3cm point C lies below line BD Link 4 (CE) - link connecting link 3 to slider link 5 Link 5 (E) - slider moving along the ground positioned 1 cm left of point F Link 6 (DF) Find the velocity of C and E in terms of velocity of B assuming that link 2 rotates counterclockwise.
Q2/ Two pulleys on parallel shaft are connected by a crossed belt. The diameter of the pulleys is 450 mm and 200 mm. The shafts are 1.95 m apart. Find (a) the length of the belt required, (b) the angle of contact between the belt and each pulley, and (c) the power transmitted by the belt when the larger pulley rotates at 100 rpm, if the maximum permissible tension in the belt is 1000 N and u = 0.25. Q3/ An open belt drive connected two parallel shafts 1.2 m apart. The driving and driven shafts rotate at 350 rpm and 140 rpm respectively and the driven pulley is 40 cm diameter. The belt is 5 mm thick and 8 cm wide. u = 0.3 and maximum permissible stress in the belting is 140 N/cm2. Determine (a) diameter of the driving pulley, (b) maximum power that may be transmitted by the belting, and (c) required initial tension in the belt.
Curvilinear Motion: Rectangular Components.
Drop-load (II) Context We want to lower a suspended load in a controlled way so that it hits the ground with a speed whose modulus is not too great. To do this, the suspended load (B) is connected by a rope passing through a pulley to another mass (A), which can move on a horizontal surface. A spring is attached to mass A to slow down the motion. Information The masses of the charges A and B are known.The pulley is a ring (a hollow cylinder) of mass mp and radius R that can rotate without friction.The surface on which mass A is placed is horizontal.There is friction between mass A and the surface it sits on, the coefficient of friction is uc.The string attached to mass A is perfectly parallel to the surface on which the mass rests.The spring is horizontal, initially unstretched and its spring constant is known. Modelization Create a model for the modulus of the velocity of mass B when it hits the ground, given the known parameters of the problem that are relevant. Mass of charge A : 75…
Q#1: Define/State the following Contact Forces and Body Forces Concentrated and Distributed Forces Static and Dynamics Laws of Motion
Given a fourbar linkage (not drawn to scale) with the link lengths L1 =d=D3 cm, L2 =a= 1 cm, L3 =b = 4 cm, L4 = c = 3 cm, 0 = 135°, Rp 2 cm, 03 600, w = 2 rad/s (CCW). For the open circuit, draw the velocities diagrams and find: %3D 1. The magnitude of VA, VBA, VB. VPA and Vp 2. The magnitude of w3, 04 Rp B AY L3 L4 03 A 02 02