Please Follow Question List the outputs of Encoder at BCD indicators for each of the eight input pulses shown in Figure; (((Remember the activates of HIGH (1) that has a LOW (0) input.))): * BCD output indicators 8s 4s 2s 1s D Encoder 4 B 6. d8 deb a (74147) 1 Add file 4444

Q: Q5: a) Design a F.A with a decoder b) Design Hexadecimal to Binary Encoder.

A:

Q: Q2/ show how an asynchronous counter can be implemented having modulus eleven with a stright binary…

A: A counter is a sequential circuit whose state represents the number of clock pulses fed to the…

Q: IS sampled, que system. The coded signal is then transmitted over a transmission channel of…

A: 53.

Q: Design MOD500 synchronous counter using 74LS161 binary counters show in figure (Q4)?

A: library ieee; use ieee.std_logic_1164.all; entity counter_16bit is Port( clock: in STD_LOGIC;…

Q: Compare between SUB & CMP instructions

A: “Since you have asked multiple questions, we will solve one question for you. If you want any…

Q: An a differential pulse code modulated system, the transmitted bits per sample is 7.  How many…

A: number of quantization level given by 2nwhere n is no of bits

Q: 5. Which one of the following devices can generate sum of product functions? 1. Multiplexer 2.…

A: SOP: SOP stands for sum of product. In this the product terms are added together. For example:…

Q: 6. Describe the operation of an OTE instruction.

A: OTE :  This is a instruction which is used in the PLC .       PLC : Programmable Logic Controllers.

Q: Implement the following function with an 8 to 1 multiplexer. Remember, you are not required to…

A:

Q: Define using your own words the sensitivity drift and bias drift, then explain how these of error…

A: Sensitivity Drift Sensitivity drift (also known as scale factor drift) defines the amount by which…

Q: 7. In a 4*1 Multiplexer, and given that 10=0, 1=0, 12=1, 13=1, and the data select lines (control…

A: Given that  In a 4*1 Multiplexer, and given that 10=0, 11=0, 12=1, 13=1, and the data select lines.…

Q: In a PCM system, if maximum frequency of the input analog signal is 5 KHz and number of levels in…

A:

Q: How are binary values represented in amplitude shift keying, and what is the limitation of this…

A: The explanation is as follows.

Q: 8. Which characteristic of IC in Digital Circuits represents a function of the switching time of a…

A: The solution is provided in the following section.

Q: If the enable pulse frequency in Figure below were halved, determine the binary numbers represented…

A: Analog to digital converter (ADC) is a device that converts the analog input voltage to digital…

Q: A 9 bit asynchronous counter has a 128 - kHz clock signal applied. i) What the mod Number of this…

A: i) The given asynchronous counter is 9 bits. The mod number of the counter is given as:  Mod…

Q: 15.a. An encoder is being used instead of a tachometer in a DC servo system. This system of speed…

A: There are a few questions related to the sensors attached to the machine to measure the speed of…

Q: Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Design ADC using VTC (Voltage to Time Converter) with clock generator fc=32HZ and the slope of…

A: Given - Clock generator frequency FC=32 Hz. Slope of voltage to time converter K=0.025 Maximum…

Q: Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted…

A:

Q: The circuit that converts continuous signal into 'n' bit binary number  is called as ___________.…

A: Given To determine which circuit converts continuous signal into n bit binary number

Q: Write an 8088/8086 assembly program that counts the length of a null terminated string that starts…

A: Microprocessor Programming : The "jargon" of directions which a specific microchip chip has is…

Q: 4 RESET is an 5- Address lines of 8086/8088 are (input, output) signal for the 8086/8088. type,…

A: Fill in the blanks for questions 4&5 ?

Q: 1. Provide a block diagram and a function table for the NOR-Gate Latch. 2. Describe, with the aid of…

A:

Q: 1) Convert and show ALL work: a) 89 to 8-bit, unsigned binary b) 254 to 8-bit, unsigned binary c)…

A:

Q: Explain on Encoders, Decoders, Multiplexer and demultiplexer(.

A: Encoders are those devices which use 2^n number of inputs and outputs are n. At most only one of…

Q: 2-bit by 2-bit binary multiplier using ROM VHDL code

A: A multiplier is an electrical circuit that multiplies two binary integers in digital electronics,…

Q: 5. Which statement is true for a priority encoder that has two inputs triggered at the same time? a.…

A: In priority encoder, the output is determined by the input with higher priority.

Q: TTL output circuits are classified into two main kinds. What are these two sorts?

A: TTL output circuits classification

Q: A 9-bit asynchronous counter has a 128-kHz clock signal applied. (i) What is the MOD number of this…

A: Given here a 9-bit asynchronous counter has a 128-kHz clock signal and here we have to find the mod…

Q: Identify the type of signal processor element? a. Variable manipulation b. Variable controlling c.…

A:

Q: Question 4 For the given circuit shown in Figure Q4, answer the following questions: a) What is the…

A: Part (d): The modified circuit diagram is shown below:

Q: How many bits are required to represent the Arduino analog input? Hint: There are 1024 possible…

A:

Q: 9. For the circuit shown in Figure Bl19a, Ve- 20V Rc = 3ko RB = 10k 2 VCE VBB-3V Figure B19a i)…

A:

Q: a) Implement decimal to BCD encoder. b) Implement full adder using decoder.

A: As per the guidelines we supposed to answer one question at a time, so please ask other questions…

Q: Differentiate between decoding logic for an active-HIGH output and an active-LOW output

A: According to the question we have to explain about,  Differentiate between decoding logic for an…

Q: In IC 74153,the input at pin number 14 is Options A-Connected to ground B-Connected to power/VCC…

A: IC 74153 has two 4-by-1 multiplexers in it. A multiplexer has four inputs for input data, 2 lines…

Q: In digital design, how important are priority encoder, decoder, and multiplexer circuits? Give 3…

A: According to the question, we need to discuss the importance of the priority encoder, decoder, and…

Q: For a PCM system with the following parameters, Parameters: (i) Maximum analog input frequency = 5…

A: It is given that: fm=5kHzDynamic range=54dBVmax=±5.01V

Q: Complete the table and timing diagram (Q0,Q1,02,0Q3) for the 4-stage synchronous binary counter…

A:

Q: calculate, the number of bits required for 8 quantization levels, quantization step size and level…

A: The number of quantization levels = L   The number of bits = n   Note  L <= 2^n  Step size (∆) =…

Q: Q2) A) Express the decimal number (- 30 ) as an 8-bit number in 2's complement form, and verifying…

A:

Q: Explain what are Encoder sensors and how does it work

A: Encoder sensors -  Encoder sensors are a form of mechanical motion sensor that converts a motion…

Q: Assume that you have an 8-bit ADC with Vref = 5 Volts. If the input voltage is 3.5 Volts, what is…

A:

Q: one method of eliminating contact bounce wherein it triggers on the first contact bounce instead of…

A: To select proper answers from options.