Inclined plane diagram:Also String 1String 2String 1BCAThe diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, asshown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionlesspulley to a hanging block, Block A. Upload a complete free body diagrams for Cart B as shown in the inclined plane diagram. Include all forces acting on Cart B. All forces must be labeled with twosubscripts using the conventions defined in our lectures and in Fliplt Physics. The file you upload for this question must include ONLY a free body diagram forCart B and NOTHING ELSE. No credit will be given for a large file that requires your instructor to find the answer to this question. Part of the point of thisquestion is to understand what belongs in a free body diagram for Cart B.

Answered: Image /qna-images/answer/0b47e080-ae7f-4dff-a98f-cfc397f66a73.jpg

plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, as shown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionless pulley to a hanging block, Block A.

plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, as shown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionless pulley to a hanging block, Block A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diagram models a juggler balancing a pole on her nose. The pole has length L and is modeled as a a mass-less rod with a point mass mp located at the distal end. The rod is attached via a friction-less pin to the cart Me. By moving her head (mass Me) she can correct any tendency for the pole to flop over. This is accomplished by supplying a force F to her head by neck muscles (not shown). This makes a nice 410 project, except that first we have to find the transfer function. Find the full non-linear dynamics equations. HINT: Use the energy method discussed in class. mp x(t) 0 Mc gl F
Example 1: Four masses m1, m2, m3, m4 are 200 kg, 300 kg, 240 kg and 260 kg, respectively. The corresponding radii of rotation are 0.2, 0.15, 0.25 and 0.3 meters, respectively, and the angles between successive masses are 45°, 75° and 135. Find the position and magnitude of the balance mass required, if its radius of rotation is set to 0.2 m. 240 kg 0.15 m 0.25 m 300 kg 120° 255° 60 45° 78 0.2 m 200 kg 0.2 m m Resultant 45 0.3 m force e a b. 40 260 kg 3
5. There are two masses with unequal weight. The masses are tied by a rope and they are connected over two pulleys as shown in Figure 1. When the system is released, heavier mass accelerates downward and lighter accelerates upward. Assume frictionless pulleys, find the theoretical tension of the thread and the theoretical acceleration. Masses are M1= 6.00 kg and M2= 2.00 kg. Two discs are allowed to move on inclined air table with dimensions a= 11cm, b=17cm, c=60cm. (Hint: You can use free body diagram and M1 b Newton' W.B. M2 s second law of a motion equation (F=m.a) to solve tension, g=980cm/s?.)
(b) The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T;and T, of V-belt just before it start rotating. M A B Øg= 120 mm Ø= 120 mm Figure Q2 (b)
The crate shown in Figure P2 has a mass of 50 ?? and the coefficients of static and kinetic friction between it and the inclined plane are 0.3 and 0.25, respectively. The angle of the plane is 45?.(a) What tension must the winch exert on the cable to start the stationary crate sliding up the plane?(b) If the tension is maintained at the value determined in part (a), what is the magnitude of the crate’s velocity when it has moved 0.5 ? up the plane?
1) A drawbridge has mass M and length L and is approximately uniform. It has a hinge at the right end, and is being pulled up via a cable (FT) that is pointed 45° up from "“to the right" and is connected at L/3 from the left end. Assume that the tension is just enough that there's no normal force at the left end of the bridge. Draw a Free Body Diagram for the bridge. Assume it is stationary and not accelerating.
A plate inside a microwave is rotating by a motor that is connected to it's center. the plate is sitting on 3 wheels , as you can see in the picture . a. Draw a forces diagram on a small wheel b. Calculate the minimum motor's torq that is needed in order to spin the plate. given: Mass of the plate: Mp Mass of one wheel :Mw Static friction coeffient: miu(s) Radius wheel : r Radius plate : R Anything else that needed just add , thank you
A 25.5 kg mass (m) is suspended by the cable assembly as shown in the figure. The cables have no mass of their own. The cable to the left (T) ) of the mass makes an angle of 0.00 with the horizontal, and the cable to the right (T;) makes an angle (02) of 40.6. If the mass is at rest, what is the tension in each of the cables, T and T; ? The acceleration due to gravity is g = 9.81 m/s?. T T = 123.52 N 123.52 TOOLS x10
The boxes are at rest. The pulley is massless. Fpull makes an angle 0 with respect to the incline. (i) Draw free body diagrams for m, and m, for the situation outlined in part (ii). (ii) What maximum force, Foull, Can you apply to m, and have it remain at rest? In terms of the given information. Just give the equation (or equations) needed to solve for the force. Do not simplify or isolate for Fpull, but make sure it is the only unknown. pull Given information: B (angle of incline with horizontal) e (angle Fpull makes with incline) m, (mass of box 1) m2 (mass of box 2) H (distance m, is above the ground) • H, (static friction coefficient, incline and box 1) He (kinetic friction coefficient, incline and box 1) m1 m2
The figure shows a mechanism that raises packages in a transfer mechanism. A 200-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 574 rpm CCW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank O2A and the force in member AB The weights of the links are negligible. 50mm 450mm 200 N 200 mm B. 374 mm 300mm The angular velocity of the link O,BD in rad/s is = Choose.. The magnitude of the velocity of point D in m/s is = Choose.. The torque required from the motor at the crank O2A in N.m is = Choose... The force in member AB in N is = Choose...
The figure shows a mechanism that raises packages in a transfer mechanism. A 300-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 400 rpm CCW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank O2A and the force in member AB The weights of the links are negligible. The angular velocity of the link O4BD in rad/s is = Answer 1 Choose... The magnitude of the velocity of point D in m/s is = Answer 2 Choose... The torque required from the motor at the crank O2A in N.m is = Answer 3 Choose... The force in member AB in N is =
Example 1: Four masses m1, m2, m3, m4 are 200 kg. 300 kg. 240 kg and 260 kg, respectively. The corresponding radii of rotation are 0.2, 0.15, 0.25 and 0.3 meters, respectively, and the angles between successive masses are 45°, 75° and 135°. Find the position and magnitude of the balance mass required, if its radius of rotation is set to 0.2 m.