KINEVAHUNIVERSITYQuizQ) An inductive proximity sensor is used to detectthe presence of car in traffic lights. The outputrcunf the sensor produces a sin oidal signal at30 KH This signal is usually mixed with a randomhigh and low frequency_noise around the signal.Design a suitable cascaded bandpass filter to removethe unwanted signals given that thof thepassband region is no more tha 10 KHZ Also,sketch the magnitude and phase response of thefilter.YSTEMS & CONTROL ENGINEERING DEPT.MOHAMMED ALMAGEDSTAGE

The problem states that an inductive proximity sensor is used to detect the presence of a car in…

Answered: KINEVAH UNIVERSITY Quiz Q) An inductive…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Generate a 2 KHz sinusoid with a Peak to Peak Voltage of 2V (+/- 1V), and generate a quantized signal when N=8 and N=16 levels. Calculate Signal to Quantization Noise Ratio (SQNR).
Signal and system problem.plz solve every step with formula
A sinusoid has a period T0 = 3 dt, an amplitude of 1.5 mVolt, and an phase = 15 degrees a. Write down the representation of this signal.b. Perform the sampling process on the above signal with a sampling frequency of Fs = 2 kHz. Write an expression for the sampled sinusoid signal and determine the digital frequency.
b) The following figure shows a sampled signal and the desired sampled signal. A digital signal processing system is required to change the sampled signal to produce the desired output signal. Desired output -3 -2 -1 0 1 2 3 4 5 Sampled signal -0.4 -0.3 ii) Determine the frequency response and magnitude response of the designed system. Calculate the magnitude response at a digital frequency of a/4.
For the given circuit below, the RF generator is set to EXT MOD, 500kHz. RF GEN 500KHZ R1 2702 R2 10K ELECTRONIC VOM 0.0047pF a) What is this circuit? b) Is there an RF signal across R2? c) Draw the expected signal waveform across R1 d) Draw the expected signal waveform across R2 e) What is the expected frequency of the signal across R2?
Signal and system problem write on paper and solve with stepwise
Draw the expected signal waveform across R1. Draw the expected signal waveform across R2. What is the expected signal frequency of the signal across R1?
Transmitter: a carrier frequency of 108 kHz and a modulating frequency of 0.3 kHz to 3.4 kHz is applied to an amplitude modulator. The USB and the LSB are both transmitted to the distant receiver, with a suppressed carrier. Receiver: the resultant USB and LSB from the transmitter are input to an amplitude demodulator. A carrier frequency of 108 kHz is reintroduced to the demodulator. Determine the following: 1. The LSB and USB at the output of the modulator. 2. The LSB and USB at the output of the demodulator.
Determine the output voltage value of a transistor amplifier circuit by frequency for 1.923 V to input voltage. Instead of. Calculate the gain in dB for the frequency given in the table. Maximum write down the frequency (s) where the gain is halved in terms of power (3dB). Frequency curve draw as
Determine the transfer function from Uin to Uut! b) Set up amplitude and phase function! c) Assume that we connect 10V (DC) as input voltage at time t-0. How much voltage is then above C2 after a long time?
For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
Design an ACTIVE band-pass filter for the midrange part of a loudspeaker so that the bandpass region is 400 Hz-2000 Hz (as defined by the -3dB points). Design the circuit so that the absolute gain is 2. a. Draw the circuit diagram and specify the resistor and capacitor values. Assume you can use either 100, 330, 500, or 1000 Ohm resistors and can select any value of capacitor. b. Sketch the frequency response (Gain [dB] vs. frequency (Hz)). Note that you will need to convert your gain to dB before plotting. Magnitude (dB) 15 10 5 midrange 12 1 -5 -10 -15 -20 -25 10 100 1,000 Frequency (Hz) 10,000 100,000

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS