d. 565.685 VIf a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is:Select one:O a. 12000 - j16000 VAO b.-12000 + j16000 VAO c. 12000 + j16000 VAO d. None of theseGiven the circuit below and the associated set of voltages and currents, the reactive Power developed by imvoltage source isFENG300 MINTERM

A good basic question on Network and power system topic or basic electrical engineering topic.…

Answered: If a Load absorbs 20 kVA at a leading…

If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA Ob.-12000 + j16000 VA Oc. 12000 +j16000 VA O d. None of these

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: If a Load absorbs 20 kVA at a lagging power factor of 0.6. Then the complex power is: Select one: O…

Q: For reactive load, the power factor is equal to Select one: O a. 90 O b.0 O c.2 O d. 1

A: Reactive load is either capacive or inductive in nature.

Q: A load of 20 + j35 Ω is connected across a 220 V source. Determine the power factor. Ans: ___ %

A: When a load contains Capacitive or inductive elements then current will not be in the same phase…

Q: 3Ω j4Ω 2/0 A A =-j20 5Ω :-j22 65 ww

Q: If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a.…

A: Load absorbed S= 10kVA Power factor= 0.6 leading Find the power in complex form

Q: Answer is Letter A. 90 microFarad. Many thanks

Q: 25. Two loads connected in parallel are supplied from a single-phase 240-V rms source. The two loads…

A: We will find active and reactive powers at load and source. Substract load 1 active power and…

Q: If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a.…

A: Complex power

Q: The total power absorbed by a certain 3-phase load is 60 kW, the reactive power being 100 kVAR. Find…

A: Given,For a 3-phase load,Absorbed power, Pab=60kWandReactive power, Pre=100 kVAR

Q: *30. Find the average power loss and power factor for each o the circuits whose input current and…

A: In this question voltage and current is given....We have to find out average power and power…

Q: If a Load absorbs an average power of 8 kW at a leading power factor of 0.8, Then the complex power…

A: Active power P= 8kW Power factor = 0.8 leading Complex power S?

Q: A load absorbs 20 kVA at a lagging power factor of 0.6. The complex power is: Select one: O a. 20000…

Q: If z = 12 - j12 ņ and i(t) = 34 cos(wt + 40°) A: what is the Power Factor in percent? 50% 5% 45%…

A: Given, Z=12-j12 Ω

Q: B- Two elements are connected in parallel. The current through one of them is 3 sin(wt-60) and the…

Q: • Find Thevenins eguivalent for the chage EL • Get the value of impedance to Find max power trars…

Q: ANSWER THE FOLLOWING PROBLEM: MAKE SURE TO SHOW YOUR COMPLETE SOLUTION AND ANSWER MUST BE IN FOUR…

A: In this question we have given three impedance in parallel ... We have to find out resultant power…

Q: Ri R 3 Find the average power consumed by the elements And the complex power Note:Set the elements…

A: Let, R1=1 ΩR2=1 ΩR3=1 ΩL=1 HC1=C2=1 F Let the current source be 1 A, Since the current source…

Q: A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin4000t) A is applied to the…

Q: Question 6 Vs 20020°V L L S. rms In the circuit in the figure; Lload draws 15 kVA with lagging power…

Q: 1. An inductive load consisting of R and X in series feeding from a 2400-V rms supply absorbs 288 kW…

Q: Two 125 V(rms) loads are connected in parallel. The two loadsdraw a total average power of 4500 W at…

A: Given data, The value of average power PT is 4500 W at a power factor of 0.96 leading. The value of…

Q: 15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be…

Q: 1. A resistor of102, an inductor of o.012H, and a capacitor of 90 µF are connected in series with a…

Q: A SINGLE-PHASE 230 AC, 60 HZ POWER SUPPLY FEEDS A 2400 WATTS AIR CONDITIONING SYSTEM, WITH A POWER…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: A resistor of 20Ω, an inductor of 0.012H, and a capacitor of 90 μF are connected in series with a…

A: The solution is given below.

Q: A given load takes 40 kVA at 50 % lagging power factor while another load connected in parallel…

Q: A voltage and current applied to a single phase load is v= 26 cos (300t+35) and i= 19 cos (250t-…

A: Given: v=25cos300t+35°i=19cos250t-20°

Q: Two impedances, Z1 = 2+j6 N and Z2 = 6-j12 N are connected in series with a 220-V 60-Hz supply. At…

Q: In the circuit shown below power factor is - -j20 62 ww -j20= j523

A: Given circuit,

Q: A voltage of 200 253"8' is applied across to impedances in parallel. The values of impedances are…

A: Given data, Voltage V=200∠53.80 Impedances are given Z1=12+j1000 Ω, Z2=10-j20 Ω

Q: A non-sinusoidal voltage (e=20+15sin2000t+ 10sin6000t+5sin8000t Volt is applied to the circuit…

A: Given:- e=20+15sin2000t+10sin6000t+5sin8000t Formula used:- Power :−V2/Z

Q: The total impedance in the polar form in ohm. The total current in polar form. The total power…

Q: A circuit having power factor of 0.8 consumes 40 W. What will be the value of reactive power of the…

A: Given, Active power, P = 40 W Power factor, cosϕ=0.8 So, sinϕ=0.6

Q: EX/ Determine te Power and te rms value : Og9=C, Cos Cwit +Oj) + Cz Cos Cwz t+0) Wi #W2 jNot get)=…

A: 1 The power of the signal is given by the expression as shown below:…

Q: Find the complex power delivered to the load that draw: 500 VA and leading power factor of 0.75.…

Q: 3. A 12020⁰ Vrms is to supply power to a welder, heater and an induction motor. A welder is a coil…

A: Current through the element Z =voltage across element / Z. Total active power from source =sum of…

Q: A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin4000t) A is applied to the…

Q: A Load absorbs 10 kVA at a lagging power factor of 0.6. The complex power is: Select one: a. 2000+…

A: The correct solution is given below

Q: If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a.…

Q: The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10…

A: We have an step down DC chopper with, DC source voltage (Vdc) = 200 V Resistive Load Impedance (R) =…

Q: Find the following a. V0 b. Total Power C. Power factor, is It leading or lagging

A: The output voltage is defined as the voltage that appears in the output of the circuit. The output…

Q: If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O…

A: A leading power factor means the impedance of the circuit is capacitive and causing the phase…

Q: The output of a station with two alternators in parallel is 40MW at 0.75 power factor lagging. One…

Q: wt V and i i. = 10 cos at A || whe

Q: If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O…

A: Apparent power/Complex power, S=VI VAActive power/Real power, P=VI×Cosϕ KWReactive power, Q=VI×Sinϕ…

Q: if a Load absorbs 20 kVA at a lagging power factor of 0.6. Then the complex power is: Select one: a.…

Q: If a three phase load consumes apparent power of 40KVA and active power of 30 KW, power factor of…

A: Given: A three phase load consumes, Apparent power, S=40 kVA. Active power, P=30 kW.

Q: If the circuit has lagging power factor, then it is called as circuit. O Capacitive O Inductive…

Q: 2. A certain load comprises of 12 -j8 ohms in parallel with j 4 ohms. Determine the overall power…

A: All u need to know Is complex numbers Impedance in parallel Power factor formula

Q: 100 A 220 V 50 Hz 0.138 H f(x) = 0 90 ohm Solver Configuration Electrical Reference

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

d. 565.685 V
If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is:
Select one:
O a. 12000 - j16000 VA
O b.-12000 + j16000 VA
O c. 12000 + j16000 VA
O d. None of these
Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im
voltage source is
FENG300 MINTERM

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
The source in the circuit shown is a sinusoidal source. The supply voltages across various elements are marked in the figure. The input voltage is: 3V- ww -14 V-10V moon It
1) Two identical voltage waveforms of difference phase angles are shown in Figure B. Write down the expression of waveforms A and B clearly. HUS Voltage (V) 8 0 K/N B 7: ST ot
244. The apparent power drawn by an a.c. circuit is 20 kVA and reactive power is 12 kVA. The real power in the circuit in kW will be
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
An inductor and a 470 ohm resistor are connected in series with a function generator. The current is 53.7mA RMS 8kHz. The reactive power is 2.32 var. Find the value of the inductance.