Please answer in typing format Given this system with externalinput x and external output z. aWrite a truth table, pinconfiguration table, and timingdiagram. b. What does thesystem do?ToT▶ QoQyoT₁T▷ Q1Q

Answered: Image /qna-images/answer/d767fc46-b334-4297-9eab-ba5efb058ea8.jpg

Answered: Given this system with external input x…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Please create a sequence recognizer that recognizes the sequence “1101.” There is one input, X and an output, Z. The circuit should recognize “1101” on X by making Z equal to “1” when the previous three inputs are “110” and the current input is 1. A) Create a state diagram (Moore machine) for the recognizer B) State transition table C) Circuit diagram
1. An 8-bit register contains the number 10000110. The serial number 11011011is applied to the input. After 5 shift pulses, what is the number in the shift register? Assume shift right operation 2. A binary number is shifted 5 positions to the left. The number therefore has been 3. A binary number must be divided by 128. How many positions must the number be shifted (and in what direction to achieve this?
(B)- Choose the correct answer for the following questions (Choose FIVE Only) 1. Assume AL register 7FH, it would become... after executed NEG AL instruction. a. 8FH b. 18H с. 81н 2. The unknown value for ????:B000H=25000H physical address is a. 001A H b. 1A00H c. 100AH 3. A microprocessor has ..... address bus a. unidirectional b. bi-directional c. Both 4. Instruction queue allows up to ........ of instruction code to be pre-fetched. a. 16 bits b. 6 bytes c. 6 bits 5. To activate the address bus or data bus in ADo-AD15 signal the .. should be either logic 1 or 0. a. MN /ΜX b. RD c. ALE 6. According to Moor's Law...... a. number of transistors on b. number of transistors on c. number of transistors on an integrated circuit an integrated circuit tripled an integrated circuit not doubles every two years every two years change.
: Choose the correct answer for the following (n. 1. .. . instructions is not valid. a. MOV DS, 3000H b. РOP СХ c. DAA 2. When the word is to be popped from the top of the stack, the value of stack pointer is... a. incremented by 1 b. incremented by 2 c. decremented by 2 3. A microprocessor has .. . Data Bus a. unidirectional b. bi-directional c. Both 4. A microprocessor requires... power supply. a. +10V b. +7V c. +5V 5. . . instruction is not conditional jump instruction a. JA b. JMP c. JE
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
Procedure: 1. Design an even/odd parity generator for 4-bit data. 2. Design a parity checker circuit for a 4-bit data. 3. Design a logic circuit for a 3-bit message to be transmitted with an even parity bit. 4. Four data bits are to be transmitted. Design a parity bit generator to give an o/p of 'l' if the number of logic l's in the message is: (i) odd; (ii) even.
a) Convert the decimal number - 239 into a signed binary number using (1) sign-magnitude method (2) 1's complement method (3) 2's complement method b) If the above decimal number is positive , that is + 239, then convert it to a signed binary number using 1 's complement method c) Do the following binary subtraction: 101111111.01111- 001011010.10110 d)Explain Types of RAM?
Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
1) Before using an accumulator within a loop it has to be initialized. 2) _We cannot use functions if we do not include the function prototype. 3) If the number of arguments in a function call does not respect the function definition it causes a syntax error. 4) A pointer can point to variables of the same data type only. 5) We can have pointers to variables that are in the same function. T 6) If a function does not take input arguments and does not return any output, then, it cannot be defined as a function. F 7) We can have variable with the same name in different functions. T 8) _It is not possible to create a variable in the main function that has the same name as a function that we have already defined. T 9) _Global variables can be accessed by all functions I 10) Pointers are only used if the function has multiple outputs. F

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS

Given this system with external input x and external output z. a Write a truth table, pin configuration table, and timing diagram. b. What does the system do? To T ▶ Qo Q yo T₁T ▷ Q1 Q