For the state of stress, as shownbelow. Draw Mohr's circle and findthe maximum principal stresses andthe maximum shear stress, thendetermine the normal and shearstresses on the planes whose normalsare at +60° and +150° with the x-axis.Show these stresses on sketch of theelement.10 MPa20 MPa10 MPaX

Answered: the state of stress, as shown v. Draw…

the state of stress, as shown v. Draw Mohr's circle and find maximum principal stresses and maximum shear stress, then mine the normal and shear ses on the planes whose normals

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: for a contour shown in figure below. 104. 102 100 the horizontal distance between point a and the…

Q: QUESTION 5 In a two-peg test of a dumpy level, the following observations are taken. What is the…

A: As per the company's policy we are supposed to answer only one question in Multiple questions.…

Q: For the beam shown, determine the following: 3. (a) Slope at A and B; (b) deflection at F, C and E.…

Q: Q- The levelling staff held at a distance of 200 m is read at 4.54 m with the bubble out of centre…

A: Given data- Distance D=200 m, No. of divisions n=2, Sensitiveness- α=25, Staff reading SR=4.54 m. To…

Q: A rectangular concrete beam 250mm wide by 300mm deep is prestressed by a force of 540kN at a…

A: ###DETERMINATION LOCATION OF PRESSURE LINE AT SUPPORT SECTION OF BEAM###

Q: What is the distance along the outside edge?

A: Given:- angle=90 degree To find:- distance along outer edge

Q: Water for irrigation is usually expressed in units of acre-feet.One acre foot is enough water to…

Q: Find the support reactions in the figure shown. Supports A and C are hinge supports. A 6 ft 250…

Q: Draw the axial, shear and bending moment diagrams for the frame shown. Draw also the deflected shape…

A: A frame with a fixed end at A and loading as mentioned is given, To determine, Shear Force, axial…

Q: A heat pump maintains a dwelling at 68°F. When operating steadily, the power input to the heat pump…

Q: 2. What are the geodetic coordinates in meters of a station with geocentric coordinates of…

Q: Solve all support reactions using the Method of Consistent Deformation. Consider B as the redundant.

A: In the method of consistent deformation, we use both equilibrium and compatibility equations to…

Q: A sluice gate used to control the flow in a horizontal channel of unit width is shown in the figure.

Q: he properties of concrete and its importance to the structure

A: Context: Concrete properties and its significance

Q: 2. Draw the influence line for (a) the vertical reaction at A, (b) the shear at C, (c) the moment at…

Q: QUESTION 6 1. The following data were taken from PEG method of adjustment. Point 1 is midway between…

A: Given:Point 1 is the midway between A and B.Distance of point 2 from A=20 mDistance of point 2 from…

Q: a. Find to the nearer hundredth centimeter the length of the stretchout

A: To find:- nearer hundredth centimeter the length of the stretchout

Q: For the beam below, (a) draw the shear and moment diagrams and (b) determine the maximum normal…

Q: An ideal continuous stirred tank reactor (CSTR) has an influent containing Chemical X at a…

Q: For a perfectly dry soil sample having specific gravity of solids as 2,68 and mass specific gravity…

Q: A bridge/joint table is exactly what its name implies. What is the substitute? What is wrong with…

A: A bridge table is a table that just holds back the keys between the two tables in a many-to-numerous…

Q: 1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at…

Q: Find to the nearer hundredth inch the length of this arc.

A: Given:- r=3 in 30 degree To find:- Length of arc

Q: The section of the masonry dam is as shown. The specific weight of water is 9.81 kN/m^3 and that…

A: GIVEN- The specific weight of water is = 9.81 kN/m^3 The specific weight of concrete is = 23.54…

Q: Q-A ship has a metacentric height of 0.90 m and its period of rolling is 20 seconds. The relevant…

A: Given data- Metacentric height- Gm=0.90 m,T=20 s, To Find- The relevant radius of gyration (k).

Q: A beam is loaded as show in the figure. Assume EI is constant. Using Virtual Work Method determine…

Q: Problem- Find the surface tension in a soap bubble of 50 mm diameter with its inside pressure being…

A: Given data: Soap bubble diameter, d=50 mm=50×10-3 m Inside pressure, P = 2.5 N/m2

Q: A rectangular concrete beam, 360mm deep and 200mm wide, is prestressed by means of fifteen 5mm…

A: Note: The given depth is 360mm but the correct answer is coming if we use 300mm. In this solution…

Q: The members CJ and CF of the loaded truss cross but are not connected to members BI and DG. Compute…

A: Use equilibrium conditions to find out reactions at supports. Apply equilibrium of member forces at…

Q: Using the method of sections, determine the kind and amount of stress in members. NOTE: LOAD AA= 76,…

Q: QUESTION 2 Given: a pipeline with length 3500 m, discharge of 200 L/s, roughness = 0.5mm, frictional…

Q: Need

A: Given Simple beam First find the reactions and obtain the shear and bending equation

Q: 3-Following are the results of consolidated-undrained triaxial tests on undisturbed soils: Confining…

A: Given, Test results for consolidate undrained (CU) triaxial test To find : Shear stress parameters…

Q: 3. Given the crest vertical curve below, a. Determine the elevation of BVC and EVC, compute also for…

Q: 3-Following are the results of consolidated-undrained triaxial tests on undisturbed soils: Confining…

A: Given, Consolidation undrained test data To find, Shear strength parameters (c' and ϕ')

Q: 4.3 Given ADT = 11000 veh per day. k = 12%, D = 0.6, lane capacity = 700 veh/h and annual traffic…

A: Given : ADT=11000 veh per day K= 12% D=0.6 lane capacity=700 veh per hour Annual traffic growth…

Q: In a 5 m wide rectangular channel, the velocity u distribution in the vertical direction y is given…

Q: What is the required plan size of a square sedimentation tank (as the primary sedimentation tank in…

Q: Determine the stresses in members CE, CF and DF of the truss shown using method of sections. 60 kN-…

A: Objective: To determine the member stresses/forces in CE, CF and DF using the method of sections.…

Q: Triaxial tests performed on samples of aeolin sand. The failure conditions in terms of effective…

A: Given Data: The failure conditions in terms of effective stress are given as:…

Q: Q-A rail engine accelerates from its stationary position for 8 seconds and travels a distance of…

A: Given- Time t=8 s, Distance s=280 m, It is needed to find the speedometer reading.

Q: The image below shows a beam subject to two couples, F₁ = 670 N and F₂ = 760 N. (Figure 4) The…

Q: 3. (a) Slope at A and B; (b) deflection at F, C and E. F 4 kN/m im A 6 kN/m 1 m- |C -1 m 4 kN/m 10

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: A cohesive soil has an angle of shearing of 30 and a cohesion of 35 kN/m2. If the specimen this soil…

A: Given- A cohesive soil, Angle of shearing- ϕ=30o, cohesion C= 35 kN/m2, Triaxial compression test-…

Q: A square footing placed at a depth of 1 m is required to carry a load of 1000 kN. Find the required…

Q: Question 3 A concrete-lined trapezoidal channel having a bottom width of 4 m convey 12 m³/s of water…

A: As per bartleby guidelines. We have to solve 1st 3 question in case of multiple question. Please…

Q: The degree of kinematic indeterminacy of the rigid frame with clamped ends at A and D shown in the…

Q: Q-The moment of inertia of a beam section 50 cm deep is 69490 cm4. Find the longest span over which…

Q: An L203x102x19.0 is used as a tension member, with 22mm dia. bolts in each leg at the usual gage…

A: Answer : We know that net area is given by For chain pattern of bolting An = Ag - ∑Ah For…

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

For the state of stress, as shown
below. Draw Mohr's circle and find
the maximum principal stresses and
the maximum shear stress, then
determine the normal and shear
stresses on the planes whose normals
are at +60° and +150° with the x-axis.
Show these stresses on sketch of the
element.
10 MPa
20 MPa
10 MPa
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

! Required information Consider the given state of stress. A 16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 15° clockwise, using Mohr's circle. The normal stress Ox'is - |ksi and Oy'is ksi. The shearing stress Tx'y'is ksi.
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
A rectangular cantiliver wooden beam is applied by point load of 400in at free end Determine cross section area and second moment of inertia about bending axis and Draw internal effects shear and bending diagram Determine direct and shear stress at A on cross section of a-a .sketch state of stress
2. A finite element analysis of a bearing housing indicates that at a point p, the material is subjected to the state of stress (in MPa): Ox Txy Txz] Txy Oy Tyz Txz Tyz 0₂ 0 -30 -10 -10 40 Determine the principal stresses and the absolute maximum shear stress. [20 20 = 20 0
! Required information Consider the given state of stress. to A16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 10° counterclockwise, using Mohr's circle. The normal stress ox'is ksi and oy'is |ksi. The shear stress Tx'y'is ksi.
1. A stepped cyllindrical bar carries axial forces as shown. What is the maximum value of P for stresses not to exceed 100 MPa in tension and 120 MPa in compression? AAB = 360mm2 ABC = 240mm2 ACE = 300mm2 5P 4P 3P A B C D 3P E חו P
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
Prob 1. The cantilever beam has the dimensions shown on the right (beam is fixed at A). Given that the beam must support the loads as shown and knowing the beam has a modulus of elasticity, E = 29 x 103 ksi: Determine the internal forces at a point 6 ft away from the wall. Be sure to include FBD. Determine the stresses acting at point C. Show all work. Determine the total normal stress (o) and the total shear stress (7) at C. Show all work. (Б) X-section view 10 k/ft 2 in? B 10 k $3 in "N.A. 10 in 6 ft 12 ft +1 in 2 int -14 in
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi
Cross section of each bar 350 mm2 . Find stress in bar CD
Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.99 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 11.7 ft and P = 92.21 kips. Round off the answer to five decimal places. 010.png В D F h H C E G -on-- 9 ft→9 ft→9 ft→-9 ft- P P
The Mohr's circle shown has coordinates X = (60 MPa, -16 MPa) and Y = (0 MPa, 16 MPa). Draw the stress element for maximum shear at the correct orientation (label the new axes, the magnitude and direction of the stresses and show the angle). (Upload your answer showing all values as well as neat and clear calculations) Y