FigureFw40°CGmgFT<1 of 1 >▼Calculate the tension Fr in the wire that supports the 42 kg beam shown in thefigure(Figure 1).Express your answer using two significant figures.FT = 320 N✓ CorrectPart BPrevious AnswersACalculate the magnitude of the force Fw exerted by the wall on the beam.Express your answer using two significant figures.Fw = 320 NPart CPrevious Answers✓ Correct✔ FigureFw40°CGmgFT<1 of 1>Express your answer using two significant figures.Fw = 320 NSubmit✓ CorrectPart C0Calculate the direction of the force Fw exerted by the wall on the beam.WExpress your answer using two significant figures.VOΑΣΦe force F'w exerted by the wall on the beam.Previous AnswersSubmitRequest AnswerĆ?0above thehorizontal

Answered: Image /qna-images/answer/4147f0ab-8683-4741-8e62-850674ff79db.jpg

Figure Fw 40° CG mg FT 1 of 1 ▼ Calculate the tension Fr in the wire that supports the 42 kg beam shown in the figure(Figure 1). Express your answer using two significant figures. FT 320 N Submit ✓ Correct Part B Previous Answers Calculate the magnitude of the force Fw exerted by the wall on the beam. Express your answer using two significant figures. Fw 320 N Submit Part C Previous Answers ✓ Correct

Figure Fw 40° CG mg FT 1 of 1 ▼ Calculate the tension Fr in the wire that supports the 42 kg beam shown in the figure(Figure 1). Express your answer using two significant figures. FT 320 N Submit ✓ Correct Part B Previous Answers Calculate the magnitude of the force Fw exerted by the wall on the beam. Express your answer using two significant figures. Fw 320 N Submit Part C Previous Answers ✓ Correct

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Introduction

Section: Chapter Questions

Problem 9WUE

See similar textbooks

Similar questions

a 46ll Asiacell| hw#3.docx 600 N Determine the magnitude of the resultant force acting on the plate and its direction, measured counter- clockwise from the positive x axis. F= 650 N F = 750 N 45° F = 900 N If F = 30 lb and F2= 40 lb, determine the angles ana o so that the resultant force is directed along the positive x axis and has a magnitude of FR=60 lb. F1
Problem 01: A force 200 N is directed as shown in figure. Determine the X and Y components of the force. Express your final answer in Kilonewton. 200 N 30° Problem 02: Determine the components of the 30u-N force directed down to the right at a slope of 2 to 3 as shown F = 300 N Problem 03: The components of a certain force are defined by . Determine the magnitude and inclination of of the resultant with the x-axis. Draw/plot your answer.
a) What is the bar force at CE in KN? b) What is the bar force at CF in KN? c) What is the bar force at DF in KN? Remember: A bar force is a vector quantity so it consists of a magnitude, a unit and a direction. (Please include direction)
SAQ 1 1.2 m D C An 80-kn'm couple shown in the plate is caused by a pair of parallel forces of magnitude F (not shown). Determine: 80 kN m a) the smallest possible value of F, and 1.6 m b) the value of F if the forces act at points A and C and are parallel to the dashed line shown at A. A В 60°
Will the 200N block shown in the figure be held in equilibrium by the force of 160N? The coefficient of static friction is 0.3. What is the actual friction force based on your calculation? P 45° Solution: A 1. There are in total 2. EF, = 0: N y 3. Fx = 0: fquired= 4. Maximum static friction fm = forces on the block, with the frictional force point to the 5. Hence the block will N; N; N; 6. The actual friction froce on the contacting surface is N
The pulley system holding a crate of unknown weight is at equilibrium. Cord BD can support a maximum load of FBD = 1860 N. www D 01 A B a. Determine the maximum weight of the crate, W. b. Determine the angle 0₁. Round your final answers to 3 significant digits/figures. ) N W = 0₁ = 12 5 13 degrees
COMPUTE THE: 1. the tension in cable BD the components of the supportAt C. 2. the resultant using cosine law(force polygon) the angle of the R measuredCW from the x – axis.
Rod AB is supported by a pin and bracket at A and rests against a frictionless peg at C. Determine the reactions at A and C when a 200-N vertical force is applied at B. A 150 mm 150 mm -180mm 200N B.
Two forces are applied to the construction bracket as shown. Determine the angle which makes the resultant of the two forces vertical. Determine the magnitude R of the resultant. Assume F₁ = 725 lb, F₂ = 390 lb, a = 69°. F₁ y T F2 O H Answers: e= i R = i lb
PART A) What is the maximum force that can be applied to a bone whose minimum cross-sectional area is 3.0cm^2? (This is approximately the cross-sectional area of a tibia, or shin bone, at its narrowest point.) Express your answer using two significant figures. PART B) Estimate the maximum height from which a 70kg man could jump and not fracture the tibia. Take the time between when he first touches the floor and when he has stopped to be 0.006s, and assume that the stress is distributed equally between his legs. Express your answer using two significant figures. Thank you!!!
A crate is supported by three cables as shown. Knowing that the tension in cable ADis 351 lb, determine the tension in cable AC . Round off only on the final answer expressed in 3 decimals and indicate unit.
Find the resultant of force Y 390 Ib MATHalino.com 12 30 1 1 300 lb 722 Ib Figure P-265