Determine the range of mass m for 2 which the system is in equilibrium. The coefficient of static friction between the block and the incline is u = 0.18. S Neglect friction associated with the pulley. Answers: (i Determine the range of mass m2 for which the system is in equilibrium. The coefficient of static friction between the block and the incline is μs = 0.18. Neglect friction associated with the pulley. m1 H₂- 19 m2 Answers: (i !m₁) sm₂si 0.156 m₁)

Determine the range of mass m for 2 which the system is in equilibrium. The coefficient of static friction between the block and the incline is u = 0.18. S Neglect friction associated with the pulley. Answers: (i Determine the range of mass m2 for which the system is in equilibrium. The coefficient of static friction between the block and the incline is μs = 0.18. Neglect friction associated with the pulley. m1 H₂- 19 m2 Answers: (i !m₁) sm₂si 0.156 m₁)

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter10: Introduction To Simulation Modeling

Section: Chapter Questions

Problem 41P: At the beginning of each week, a machine is in one of four conditions: 1 = excellent; 2 = good; 3 =...

See similar textbooks

Similar questions

At the beginning of each week, a machine is in one of four conditions: 1 = excellent; 2 = good; 3 = average; 4 = bad. The weekly revenue earned by a machine in state 1, 2, 3, or 4 is 100, 90, 50, or 10, respectively. After observing the condition of the machine at the beginning of the week, the company has the option, for a cost of 200, of instantaneously replacing the machine with an excellent machine. The quality of the machine deteriorates over time, as shown in the file P10 41.xlsx. Four maintenance policies are under consideration: Policy 1: Never replace a machine. Policy 2: Immediately replace a bad machine. Policy 3: Immediately replace a bad or average machine. Policy 4: Immediately replace a bad, average, or good machine. Simulate each of these policies for 50 weeks (using at least 250 iterations each) to determine the policy that maximizes expected weekly profit. Assume that the machine at the beginning of week 1 is excellent.
Find the discharge coefficient, threshold heat flux, combustion efficiency and emissivity factor for both propane and butane separetly. The pipe which would contain thesge gases is 30 inches in diameter and has an operating pressure of 1000psig.
Question 2: Consider again that the company making tires for bikes is concerned about the exact width of its cyclocross tires. The company has a lower specification limit of 22.8 mm and an upper specification limit of 23.2 mm. The standard deviation is 0.15 mm and the mean is 23 mm. What is the probability that a tire will either be too wide or too narrow?
Problem 6-2 (Algo) Rachel loves to bake cookies, but she has an old oven that has trouble maintaining a constant temperature. If the acceptable temperature range for making the cookies is 350 plus or minus 10 degrees, what is the allowable standard deviation in the temperature of her oven in order to achieve a Six Sigma level of quality? Note: Round your answer to 3 decimal places. Standard deviation degrees
6. List and explain in detail why we include disturbance term or error term in the model?
Your cafeteria is serving chicken noodle soup today, which it sources from adistributor and then warms up locally in the kitchen. The soup now sits in a large bowl anda server uses a large ladle to fill the soup into the smaller bowls handed out to the students.Consider the following variables:• Outside temperature.• Duration that the soup was heated before being put in the bowl.• Temperature of the soup in a student’s bowl.• Temperature level to which the soup is warmed up.• Insulation of the bowl used for storing the soup.• Duration that the soup bowl is open when the server inserts the ladle to serve a student.Which of these variables are (a) input variables, (b) output variables, and (c) environmentalvariables?
42. A large national producer of appliances has traced customer experience with a popular toaster oven. A survey of 5,000 customers who purchased the oven early in 2000 has revealed the following: nd ity Number of Year Breakdowns 2000 188 2001 58 2002 63 2003 72 2004 54 2005 71 a. Using these data, estimate på = the probability that a toaster oven fails in its kth year of operation, for k = 1, . . . , 6. b. What is the likelihood that a toaster oven will last at least six years without failure based on these data? c. The discrete failure rate function has the form r; = Pr/Rp–1, where Rỵ is the prob- ability that a unit survives through period k. Determine the failure rate function for the first five years of operation from the given data. d. Suppose that you purchased a toaster oven at the beginning of 2004 and it is still operating at the end of 2007. If the reliability has not changed appreciably from 2000 to 2007, use the results of part (c) to obtain the probability that it will…
The following data was recorded while observing the increase in the number of butterflies in two different ponds, Pond A and Pond B. Number of Butterflies Present Over 5 Years Year Pond A Pond B 0 50 65 85 1 2 3 4 5 100 O 110 121 133 146 161 110 143 186 What is the rate of growth, r, for each pond and which pond has the fastest average rate of growth over the five years? TA = 1.1, TB = 1.3, mg = 3.72 butterflies/yr TA=0.9, TB=0.8, mg = 3.72 butterflies/yr TA=0.9, TB=0.8, mg=27.2 butterflies/yr TA = 1.1, TB = 1.3, mg=27.2 butterflies/yr
In hydraulic fracture test, an induced fracture was created at 12.8 MPa. The fracture was reopened in three subsequent cycles. The reopening pressure at third cycle was found to be 6.4 MPa. If the tensile strength of rock is 6.3 MPa, and the pore water pressure is negligible. Determine the maximum and minimum principle stresses if the shut - in pressure was found to be 5.9 MPa
SCENARIO B: A woodcutting operation has a target (nominal) value of 200 inches and consistently averages 200.1 inches with a standard deviation of .05 inches. The design engineers have established an upper specification limit of 200.25 and a lower specification limit of 199.75 inches.
Problem 1: Auto pistons at Wemming Chung’s plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: Day Mean (mm) Range (mm) 1 156.9 4.2 2 153.2 4.6 3 153.6 4.1 4 155.5 5.0 5 156.6 4.5 a) What are the UCL x (line on top of x, counldn't find the button to do it) and LCL x (line on top of x) , using 3σ? Plot the data. b) What are the UCL R and LCL R , using 3σ? Plot the data. c) Is the Process in Control? (Please screen shot the EXCEl if its in excel) Note:- Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. Answer completely. You will get up vote for sure.
Discuss what we mean by multipole moments.