(d) Calculate the following for the AC signal V(t) - voltage at time t (seconds) given by theequationV(t) = 83V2 sin (471t) v(1)(i) Find the peak value of the signal(ii) Find the frequency of the signal(iii) Draw a labelled voltage-time graph of the signal(iv) Determine whether the RMS value of the signal is larger than the average valueor not. Why is this so?(v) Find the instantaneous voltages at 3.25ms and 5 ms. Mark these values on thesignal graph.

(d) Calculate the following for the AC signal V(t) - voltage at time t (seconds) given by the equation V(t) = 83/2 sin (471t) v (1) %3D (i) Find the peak value of the signal (ii) Find the frequency of the signal (iii) Draw a labelled voltage-time graph of the signal

(d) Calculate the following for the AC signal V(t) - voltage at time t (seconds) given by the equation V(t) = 83/2 sin (471t) v (1) %3D (i) Find the peak value of the signal (ii) Find the frequency of the signal (iii) Draw a labelled voltage-time graph of the signal

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Related questions

Q: Obtain the Clased Loop traaster fuachion Ris) by using Mason's larmula fy th splam belouws -H

Q: 2) An electronic device with a pn junction is used to make a computer. If the speed of the computer…

A: Reverse bias: It means that apply the high voltage on the cathode side of the diode and low voltage…

Q: D4.6. If we take the zero reference for potential at infinity, find the potential at (0, 0, 2)…

A: Given data Linear charge density ρL=12nC/m The given location is ρ=2.5m z=0

Q: A radio receiver consists of an RF amplifier, a mixer and an IF amplifier with the following…

A: According to the question, for the given communication system, we need to find a) Calculate the…

Q: 2c What capacity would result if the pump rpm is increased to produce a pumping head of 120 ft,…

A: It is given that: N1=100 rpmQ1=500 gpmH1=90 ftη=0.60H2=120ft

Q: Question 5 Design a circuit to accomplish the following if statement If ( XW) && (N=0) Then (Q-…

A: Logic diagram can be drawn to any circuit, by using the logic diagram the behavior of the system to…

Q: 5A 3Ω 2Ix

Q: Determine the output voltage in V when R1=9 kohm, R3-6 kohm, R5-13 k-ohm, R7=102 ohms, Reference…

A: The given circuit diagram is shown below: It is given that: R1=9 KΩ=9×103 ΩR3=6 KΩ=6×103 ΩR5=13…

Q: Which of the following set of circuit elements have a common function? a resistor, capacitor,…

A: The solution is given below

Q: (c) In a system there are three buttons. (A, B and C) and a lamp (X). The lamp only comes on if the…

A: We need to draw the logic circuit for the above statement using any suitable gates and also we need…

Q: A series RLC circuit is operated at a frequency different from its resonant frequency. The operating…

Q: 1. (а) Draw the block diagram of the feedback system and derive an equation to show that negative…

A: for our policy , i can solve only 1st question

Q: 2. Determine the indicated parameters across terminals a and b. Consider each of the networks…

Q: Q1 Choose the correcet answer for each of the following: 1. The off-delay timer (TOF) starts timing…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: A 3-phase, star-connected alternator is rated at 15000 kVA, 11 kV. The armature resistance is I-5…

A: The solution is given below

Q: 7.5 kN 5 kN 10 Vo 2 kn 6V - Vout Determine I and Vout

A: The solution is given below

Q: The parameters of the -. are defined in general terms for any operating ---_equivalent circuit…

A: The solution is given below

Q: a) Write the next-state equations for the flip-flops and the output equation. p) Construct the…

Q: Explain this diagram

A: According to the question, we need to explain the two-stage OP-AMP circuit as shown below

Q: A series RL circuit is connected to a sinusoidal voltage v with frequency . Assuming v is the…

A: Solve the problem

Q: Question 1 Determine the pulse duration of a periodic pulse train whose duty cycle is 15% and period…

Q: Question-1 Figure below shows a feedback transconductance amplifier utilizing an op amp with open…

A: The given circuit diagram is shown below:

Q: A filtered 4 diode full wave rectifier circuit wit the following specifications: The line load is…

Q: (i) For the circuit below, draw the output waveforms for both the given input wave- forms. (ii) How…

Q: Find Vo in the network 4 kN 니 mA 8 kN 3 kN 6 kN 4 k2 24V(+ 6 ΚΩ Vo 12 kN 12 kN

Q: The magnetic core in Figure 3. has a mean core length of 80 cm, and its uniform cross-sectional area…

A: The solution is given below

Q: Question A: For the parallel resonant network in figure QA: a) Calculate f,. b) Determine Q, using f…

A: Given:

Q: The EMF and resistor voltage in a series RLC circuit are shown as functions of time. Part A Choose…

A: The solution is given below

Q: 2. What binary word would represent the decimal number 14 if Table 1.1 were continued? TABLE 1.1…

A: Binary of a decimal no is calculated by 2 method First by table continue decimal to binary follow…

Q: Three impedances Z = 4 - j3 ohm , Z = 3 + j4 ohm and Z in delta across a 220V , 3-phase balance…

Q: What is the power gain in dB of the given circuit? 16 V 270 k2 B = 110 I 2.7 k2

Q: Calculate the value of voltage regulation of a power supply used by an engineer in his prototype.…

Q: 1. A3-phase, star-connected alternator is rated at 15000 kVA, 11 kV. The armature resistance is 1-5…

A: The solution is given below

Q: Šolve the next block diagram Find the out pu t C(2) in the z domain

Q: A series RLC circuit consists of a 10Ω resistor in series with L = 10µH and C = 100µF. Determine a…

Q: 3. Solve for branch currents using any metthod.

Q: +15 V 18 kn Ip = 3 mA VasoFF = -4 V 1 kn 12 kn 2 kn 2.7 kn3 Determine a) the gm b) Input resistance…

A: As per our company guidelines we are supposed to answer only first 3 subpart kindly repost the other…

Q: Determine the dynamic AC resistance of the diode characteristics with a 2mA of current using the…

Q: If the DC Supply of an amplifier is set to Zero, the output AC power will be_ a. Negative O b.…

Q: Find the equivalent resistance.

Q: FIND THE INVERSE LAPLACE OF THE FF.: 10 18 F(s) || s-4 (s-5)* 2 s +9 S (s-5)

Q: Problem No. 1 (PI) For the common-base configuration (re model), an ac signal of 10 mV is applied,…

A: Brief description : In the above given question they have mentioned a common base amplifier circuit.…

Q: (c) For the following resistive network (i) Find the equivalent resistance. Show each step. (ii)…

Q: Find H(X), P(X, Y), and H(Y) for given channel shown in figure, given that P(X1) =0.2, P(X2) =0.5,…

A: According to the question, for the given discrete channel as shown below We need to find H(X), P(X,…

Q: For the ladder network in Fig. 3.24, determine the g parameters in the s domain. 1 H ll 1H ll 1Ω 1Ω

Q: Question A: For the parallel resonant network in figure QA: a) Calculate f. b) Determine Q, using f…

A: Bandwidth: It is the range of the frequency in which different frequencies lies and outside the…

Q: when a 20 v square wave is connected across a 50 volt ac voltmeter,it's reading (in volts) will be

Q: #4 FIND i(t), t>0 t=0 122 36V 2H

Q: 3. Based on the figure below, calculate the following: a. electric current that flows in the circuit…

A: We need to find current and voltage for given circuit

Q: Problem No. 1 (PI) For the common-base configuration (re model), an ac signal of 10 mV is applied,…

A: Given: CB configuration Ie=0.5mA alpha=0.98 Vi=10mV We need to determine the base current

Question

(d) Calculate the following for the AC signal V(t) - voltage at time t (seconds) given by the
equation
V(t) = 83V2 sin (471t) v
(1)
(i) Find the peak value of the signal
(ii) Find the frequency of the signal
(iii) Draw a labelled voltage-time graph of the signal
(iv) Determine whether the RMS value of the signal is larger than the average value
or not. Why is this so?
(v) Find the instantaneous voltages at 3.25ms and 5 ms. Mark these values on the
signal graph.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
2. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on at 500µs/cm and volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find (a) the frequency, (b) peak to peak voltage, (c)the amplitude and (d) the rms value
For the waveform shown, determine: (a) Peak to Peak value (b) Peak value () RMS value (d) Frequency. If volts/div is 3V/div and Time/div is 25ms/div (No need to show the calculations)
1. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 500µs/cm and the volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find for the waveform a) the frequency, b) the peak to peak voltage, c) the amplitude, and d) the r.m.s value
Determine the rms value for each of the waveforms below.
A complex voltage waveform which has an rms value of 240V contains 30% third harmonic and 10% fifth harmonic, both of the harmonics being initially in phase with each other. (a) Determine the rms value of the fundamental and each harmonic. (b)Write down an expression to represent the complex voltage waveform if the frequency of the fundamental is 31.83 Hz.
Determine the rms value for the waveform
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
3. A sinusoidal waveform is displayed on a c.r.o. screen. The peak-to-peak distance is 5 cm and the distance between cycles is 4 cm. The 'time ' switch is on 100 µs/cm and the 'volts/cm' switch is on 10 V/cm. Determine (i) angular frequency (ii) peak (iii) rms value of voltages (iv)Time period and (v) form factor.
Derive the formula for the RMS value for the following.
Given the RMS value of the following voltage waveform is sqrt(8/3) , determine the maximum value, B, of the waveform.
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequency of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms - (iii) Determine phase relationship between voltage and current waveform. (c) From the measurement process, the circuit generated two different outputs, V,(t) and V,(t) with the same peak voltage. The V,(t) lagging V,(t) by 100°. If V,(t) =150sin(1000t – 40°)V , determine the RMS value and phase angle of.