Construct a calibration curve based on the following data: Concentration Fe 0.100 0.500 2.00 4.00 7.00 (ppm) Absorbance 0.0122 0.0608 0.2322 0.455 0.5858 Use LINEST to find the slope and intercept and their uncertainties. Enter your answer as a number with no units to three significant figures. 0.085 0.037 b 0.100 0.500 Sm Sp r2 0.958 0.037 Sy

Construct a calibration curve based on the following data: Concentration Fe 0.100 0.500 2.00 4.00 7.00 (ppm) Absorbance 0.0122 0.0608 0.2322 0.455 0.5858 Use LINEST to find the slope and intercept and their uncertainties. Enter your answer as a number with no units to three significant figures. 0.085 0.037 b 0.100 0.500 Sm Sp r2 0.958 0.037 Sy

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section: Chapter Questions

Problem 77PS

See similar textbooks

Similar questions

During your experiment, you measure the absorbance of a sample to be 1.362. You have to convert thisabsorbance to methylene blue concentration (in ppm) using the absorbance measurements of two standardsolutions of known concentration:5 ppm: Absorbance 0.55510 ppm: Absorbance 1.211What is, in ppm, the concentration of your sample? Report using 3 decimal figures. Your answer must becorrect to 0.02 ppm
This question has multiple parts. Work all the parts to get the most points. A solution of a dye was analyzed by spectrophotometry, and the following calibration data were collected. Dye Concentration Absorbance (A) at 475 nm 0.50 x 10 M 0.24 9. 1.5 x 10 M 0.36 2.5 x 10 M 3.5 x 10 M 4.5 x 10 M 0.44 0.59 0.70 a Construct a calibration plot, and determine the slope and intercept. Slope = y-intercept =
10 Wavelength, 1. (nm) E (Red, µ.Mcm- ɛ(Yellow, µMr'cm¬1) Absorbance 500 0.0369 0.000549 0.405 430 0.00506 0.0167 0.474 An orange colored solution is prepared by mixing a red dye solution with a yellow dye solution and the absorbance was measured at the analytical wavelengths of 430 nm and 500 nm. The table provides the molar absorptivity for the red and yellow dye at each analytical wavelength. Calculate the concentration (in u.M) of the red and yellow dye in the mixture. [red] = [yellow] =
You are measuring the concentration of an unknown protein sample, and the absorbance at 595 nm (or A595) of your unknown is greater than that of the highest-concentration standard solution. It is not advisable to simply extrapolate the line of the standard curve to calculate the concentration of the unknown In this scenario, what would be the best strategy to measure the concentration of your unknown (instead of extrapolating from the standard curve)? (answer in 5 sentences)
A calibration curve is made for the absorbance as a function of concentration of blue dye (in mg/L). The slope of the curve is 0.131; the y-intercept is -0.01869; the correlation is 0.993. If a consumer sample has an absorbance of 0.120 on the same instrument, what is its concentration of blue dye, in mg/L? a. 0.034 b. 0.935 c. 0.993 d. 1.06
To test a spectrophotometer’s accuracy, a solution of 60.06 ppm K2Cr2O7 is prepared and analyzed. This solution has an expected absorbance of 0.641 at 350.0 nm. Several aliquots of the solution produce the following absorbance values. 0.640    0.638    0.640    0.639    0.640    0.639    0.638 is there any significant difference between the experimental mean and the expected value at a 99.9% confidence level? Question 21 options: Yes because tcal<tcritical Yes because tcal>tcritical No because tcal<tcritical No because tcal>tcritical
A protein’s concentration can be determined spectrophotometrically by mixing it with an indicator called a Bradford reagent and measuring the amount of light absorbed by the protein. Use the plot below to determine the mass of protein (in micrograms, μμg ) in 100.0 mL of the solution if its absorbance is 0.398. A. 52 B. 3.1 C. 2.4 D. 0.52 E. 0.031
What is the significance of the max of a spectrum? What are the other uses of the spectrophotometer?
The absorbance of an unknown dye solution is measured to be 1.06 by a spectrometer. The calibration plot of the spectrometer is provided below. What is the molar concentration of the unknown sample (in mole L)? Absorbance vs. Molarity 18 y3 67024x-0.0343 16 14 12 1 0.8 0.6 0.4 0.2 01 0.2 0.000005 00001 0000015 Concentration of solutions, mol/L 0.00002 0.000025 000003 0 163e-5 O 2.35e-6 0 163 0 235 Absorbance
A standard curve of absorbance vs. concentration has a linear trendline of y = 0.56x + 0.987. Use this trendline to calculate the concentration of an unknown sample that has an absorbance of 1.245.
You are measuring the concentration of an unknown protein sample, and the absorbance at 595 nm (or A595) of your unknown is greater than that of the highest-concentration standard solution. It is not advisable to simply extrapolate the line of the standard curve to calculate the concentration of the unknown In this scenario, what would be the best strategy to measure the concentration of your unknown (instead of extrapolating from the standard curve)?
Unrounded Rounded ε∗,L/μmol 0.0259825 0.0260 Heres the data if needed: TZ # Concentration Absorbance at 430 nmnm 1 33.6480 0.931 2 25.2360 0.757 3 16.8420 0.210 4 8.41200 0.137 5 4.20600 0.122