Cc = 0.2 and An oedometer test on a saturated clay soil gave the following results: Cs = 0.04. The in-situ vertical effective stress in the field is 130 kPa. A building foundation will increase the vertical stress in the center of the clay by 150 kPa. The thickness of the clay layer is 2 m and its water content is 28%. Calculate the primary consolidation settlement of the clay layer in the field if: a). OCR = 4.5; b). OCR = 1.5.

Cc = 0.2 and An oedometer test on a saturated clay soil gave the following results: Cs = 0.04. The in-situ vertical effective stress in the field is 130 kPa. A building foundation will increase the vertical stress in the center of the clay by 150 kPa. The thickness of the clay layer is 2 m and its water content is 28%. Calculate the primary consolidation settlement of the clay layer in the field if: a). OCR = 4.5; b). OCR = 1.5.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Similar questions

A clay sample was consolidated in a triaxial cell under a backpressure of 50 kPa and cell pressure of 150 kPa. The drainage valve was then closed and the cell pressure was increased to 200 kPa when the pore pressure increased to 98 kPa. What is Skempton’s B-parameter? The above sample was then subjected to a vertical deviator stress, which was increased from zero under undrained conditions. The sample failed when the pore water pressure was 160 kPa and the deviator stress was 70 kPa. What is Skempton’s A-parameter at failure? Assuming the clay is normally consolidated, find the friction angle in terms of effective stresses.
For a laboratory consolidation test on a clay specimen (drained both sides), the following were obtained. Thickness of the clay layer = 25mm o_1 = 200KN/m^2 o'2 = 400KN/m^2 e_1 = 0.73 e_2 = 0.61 Time for 50% consolidation (t_50 = 2.8min: From table U = 50%, Tv = 0.197 %3D Determine the hydraulic conductivity (in cm/sec) of the clay for the loading range.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3.
For a laboratory consolidation test on a clay specimen (drained on both sides) the following results were obtained: Thickness of clay soil= 25 mm; P_1 = 50 kPa; P_2 = 120 kPa; e_1 = 0.92; e_2 = 0.78; Time for 50% consolidation= 2.5 min. Tv = 0.197. Determine the hydraulic conductivity of the clay for the loading range in m/min. Show diagram
A sample of coarse sand, 15cm high an 5.5 cm in diameter, was tested in a constant-head permeameter. Water percolate through the soil under a hydrostatic head of 40cm for a period of 6.0s. The discharge water was collected and found to weigh 400g. What was the coefficient of permeability at the void ratio and temperature of the test?
The following data were obtained when a sample of medium sand was tested in a constant head permeameter:
A clay sample was consolidated in a triaxial cell under a backpressure of 50 kPa and cell pressure of 150 kPa. The drainage valve was then closed and the cell pressure was increased to 200 kPa when the pore pressure increased to 98 kPa. What is Skepton’s B-parameter? The above sample was then subjected to a vertical deviator stress, which was increased from zero under undrained conditions. The sample failed when the pore water pressure was 160 kPa and the deviator stress was 70 kPa. What is Skempton’s A-parameter at failure? Assuming the clay is normally consolidated, find the friction angle in terms of effective stresses.
It is known that a particular deposit of clay has the following shear strength parameters: c' = 15 kPa, o' = 23°; Cu = 10 kPa, cu = 13° A sample of this clay is consolidated in a triaxial cell to an all-round pressure (03) of 250 kPa. The sample is then sheared by increasing 0₁, keeping 3 constant and the drainage valve closed. What is: i) ₁ at failure? ii) Pore water pressure inside the sample at failure? iii) Final values of 0₁' and 03'? iv) Value at failure of Skempton's pore pressure coefficient A?
An undisturbed sample of clay, 24 mm in thickness, is tested in a consolidometer. The total change in the thickness of the specimen in 4.74 mm when the applied pressure is 200 kN/m² and 6.13 mm when the applied pressure is 400 kN/m. On reducing the pressure to zero, the specimen swells to a thịckness of 18.50 mm. The final water content of the specimen is 32.6% and specific gravity is 2.72. The clay stratum, 1 m thick, is sandwiched between pervious strata, and is subjected to an overburden pressure of 200 kN/m². Estimate the probable settlement of a proposed structure, if due to its construction, the effective pressure at the centre of the clay layer is expected to be increased to 400 kN/m². don't try to solve this question, otherwise
Subject: Soil Mechanics Please provide a solution and a diagram For a laboratory consolidation test on a clay specimen (drained on both sides) the following results were obtained: Thickness of clay soil= 25 mm; P_1 = 50 kPa; P_2 = 120 kPa; e_1 = 0.92; e_2 = 0.78; Time for 50% consolidation= 2.5 min. Tv = 0.197. Determine the hydraulic conductivity of the clay for the loading range in m/min. a. 1.081 x 10^-3 b. 2.56 x 10^-2 c. 1.31 x 10^-7 d. 1.23 x10 ^-5
A series of previous tests has established that the ultimate effective friction angle of a NC clayey soil is 19.2°. If a CD test is now performed on this soil with a cell pressure of 105 kPa, what would be deviator stress at failure? Given: o3 = Kao, where Ka 1-sin o' 1+sin o'
Two soil sample A and Bhave porosities n₁ = 40% and ng = 60% respectively. What is the ratio of void ratios e: eg? A (a) 2:3 (c) 4:9 (b) 3:2 (d) 9:4