Calculate the beam deflection at point C. E = 206.8 GPa, In = 1.873 x 10-6 m4. Use either the double integration method or the moment area method. Show your work. 200 N 500 N 50.8 mm 76.2 mm C 1m 1m 2 m

Calculate the beam deflection at point C. E = 206.8 GPa, In = 1.873 x 10-6 m4. Use either the double integration method or the moment area method. Show your work. 200 N 500 N 50.8 mm 76.2 mm C 1m 1m 2 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.6.5P: -5 Calen1ate the deflections S 3a nd

See similar textbooks

Related questions

Q: P (kN) 2 (kN/m) 1kN/m (a) m 1m

Q: . Figure shows a simply supported beam of span 5m carrying two point loads. Find a). The deflection…

Q: * For the RIGID beam shown, find the :deflection at point B 50 kN A B C 2m 3m 3m +0,025 m ID

A: Value of EI is needed

Q: A cantilever beam has a length L =12 ft anda rectangular cross section (b = 16 in., h = 24 in.).…

A: Calculate the moment of inertia of the beam. I=bh312 Here, I is the moment of inertia of the beam, b…

Q: A simply supported beam of length 5m, with a hollow rectangular cross-section outer width of 45mm x…

Q: A steel canthlever fAom a mefers Is loaded hith uniformly distributed . wall of 20 kN/m. Yun. Find…

Q: cantilever beam with length l is carrying a uniformly distributed load, w. What is the maximum…

A: we have to determine the deflection of the free end of the cantilever UDL

Q: For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the…

A: Use simply support beam concept to solve this problem, Given information Total length of…

Q: A beam is 18m long and it's one overhang side is subjected to a uniform load of 6kN/m. f the modulus…

A: Given: The length of the beam, L = 18 m The load on the beam, w = 6 kN/m The modulus of elasticity,…

Q: 1. A semi-infinite steel beam of second moment of area I, = 4.0 × 10° mmª is supported on an elastic…

A: Write the given information.

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 27000 ksi; / = 450…

Q: A beam with the cross-section shown is carrying a bending moment of M. Calculate the maximum bending…

Q: A cantilever beam carries a varying load as shown in the figure. If E=200,000 Mpa and =120x106 mm4…

Q: A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its…

A: Given data: Length of the beam, L=5 m. Beam is simply supported at it's ends with a concentrated…

Q: For the beams below, determine the location of the maximum deflection using double integration…

Q: Total Length Of the beam L = 50 cm, LI= 17.5 cm and self weight of beam = 5 N Load Fi = 1.2 N,…

Q: Find the maximum deflection, in inches, for 16ft. long steel beam (E=30x10^6psi) that has 2''x2''…

A: We have to find deflection of beam

Q: A rectangular section cantilever beam 200 mm wide by 400 mm deep and 2 m long carries a vertically…

Q: For the simply supported beam shown in Fig. Q1. Determine: a) The equation of the elastic curve. b)…

A: Elastic curve is defined as the deflected curve of the beam when subjected to some load.load may be…

Q: A W310 x 129 I-beam, made of A36 steel, is shown in the figure. This I-beam is 4 m long and has a…

Q: A cantilever 8m long carries a uniformly distributed load of 12kN/m from midspan to free end.…

Q: Assume that El is constant for the beam. Let w = 9 kN/m, L = 5.0 m, E = 190 GPa, and I = 105 x 10°…

Q: A cantilever beam (Fig. 1) has its left end fixed into a wall, and free end on the right. The…

Q: The beam shown below is made of 310 UB 46.2. What is the value of maximum compressive stress in this…

A: Draw the free-body diagram of the beam.

Q: QUESTION 3 Calculate the vertical deflection at point 'A' for the thin curved beam shown in figure…

Q: find the slope and deflection equations for the beam shown. Determine vertical deflection at point…

Q: ..s) The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform…

A: we have to calculate the deflection without rod

Q: P a В A 8 m Question 1 Using double integration method, determine the maximum deflection (EIO) in a…

Q: Using the Double Integration Method. for the given cross- section of the beam below, find the ff.…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: For a 150 mm x 150 mm beam shown below with E = 205 GPa, select in the %3D choices the value that…

Q: Find the slope and deflection equations for the beam shown. Determine the vertical deflection of…

Q: 03 The experimental data for the cantilever shown was given in table Find the modulus of elasticity…

A: As per given question Given data Weight =3N Deflections =2.87mm We have to determine modulus of…

Q: A) Calculate the deflection and rotation at point (c) for the beam showing in figure by using unit…

Q: P B C |A LAB LBC

A: FBD: Ay= Reaction force at AMA=reaction moment at AConvert the loading condition by this (fig 2)From…

Q: ..s) The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform…

Q: Find the deflection at the mid-point BC of the loaded beam as shown in the figure by the double…

Q: Refer to the previous problem. Calculate the resulting maximum positive moment (kN-m). O 77.4 O 96.8…

Q: A fixed-end beam is subjected to a pointload at mid-span. The beam has a rectangular crosssection…

A: given; →P=12KN =12*103N→L=4m =4*103mm→hb=2→E=11GPa =11*103MPa (a)maximum deflection(δmax)=2mm

Q: mm by 500 mm, methods discussed find the deflection at the free end. Use E 200 GPa Assume P equals 8…

A: Reaction When beam is subjected to load then to keep beam in equilibrium there must be reaction…

Q: Calculate the deflection and rotation at point (a) for the beam showing in figure by using unit load…

A: Deflection If the beam undergoes some load on it then deformation in the beam takes place and this…

Q: b. Determine the deflection of the beam at midpoint for the beam loading system shown in the figure…

Q: I. Solve the following problem, complete with free body diagrams, clear solutions, and complete…

Q: For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 5.7…

Q: For the beam shown below, B L- t-1/2- assuming that E= 60 Mpa, I= 60*10 m, and w= 20 N/m. What is…

A: GIVEN :- E=60MPa I=60x10-6 m4 w=20N/m x=0.5m DIAGRAM :- Figure:1. Figure :2.

Q: Compound beam ABC is loaded by pointload P 51.5 kips at distance 2a/3 from point A anda triangularly…

A: given; lets take reaction force at A=RAlets take reaction force at…

Q: For a 200 mm x 200 mm beam shown below with E = 20 GPa, select in the %3D choices the value that…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Calculate the beam deflection at point C. E = 206.8 GPa, I„ = 1.873 x 10-6 mª. Use either the double
integration method or the moment area method. Show your work.
200 N
500 N
50.8 mm
-------z
76.2 mm
A
1 m
1 m
2 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the plastic modulus Z and shape factor/for a W 12 x 14 wide-flange beam. Obtain the cross-sectional dimensions and section modulus of the beam from Table F-l(a) in Appendix F.
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
-5 Calen1ate the deflections S 3a nd
A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
A cantilever beam of a length L = 2.5 ft has a rectangular cross section {b = 4in,, h = Sin,) and modulus E = 10,000 ksi. The beam is subjected to a linearly varying distributed load with a peak intensity qQ= 900 lb/ft. Use the method of superposition and Cases 1 and 9 in Table H-l to calculate the deflection and rotation at B.
70 mm Mx G 165 mm Mx = 79ヒNm %3D 60 mm 190m Mx affects the cross section digure. Calculate the noral stress values The bending moment of the beam given in n that will occur at the points I,2, 3 of the beam sectio and draw the noral stress distribution.
For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the beam at A, and (b) the deflection Vmidspan of the beam at midspan (i.e., x = 2.45 m). Assume a constant value of El = 1270 kN-m² for the beam; M₁ = 9 kN-m, wo = 19.8 kN/m, LAB = 1.1 m, LBc = 2.7 m. MA A Answer: (a) VA = (b) Vmid i LAB i Wo B LBC mm. mm.
For the beam shown, use only singularity functions. V₁ = 45 lbf/in and V/₂ = 5 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 0 1400 lbf Hinge JA B₁ C R₂ R₁ 4 in 4 in 2 in V1 V2 D R₂ + What is the value of the peak moment between points Cand D? The peak moment between points C and Dis Ibf.in.
The cantilever beam shown is subjected to a concentrated load of P=70800 lb. The cross-sectional dimensions and the moment of inertia of the W16x57 wide-flange shape are: d = 16.4 in. tw=0.430 in. by=7.12 in. ty=0.715 in. 1₂-758 in.4 Compute the value of the shear stress at point H, located at y = 4.8 in. below the centroidal xis. H Answer: Shear stress = psi
Calculate the maximum deflection at point B in the beam below: (answer in mm) The beam is a steel wide flange where: E = 210 GPa I = 225 x 10-6 mª 2.5m 2.5 kN/m 4 m 5kN B
For the steel cantilevered beam shown, determine the minimum moment of inertia of the structural tee section, Imin if the deflection at the free end is limited to 1.2 in. -L2 Given: .L=19.6 ft • L₂ = 6.6 ft F = 1200 lb • q = 1.05 kip/ft Imin=-512.6 79 - ¹/2 |F L +4₂+ L2 H q a