Please I need the answer as soon as possible please (b) (i)Although both voltmeter and oscilloscope can measure voltages,however an oscilloscope can provide more information on voltagescompared to the voltmeter. What are the information that can be providedby an oscilloscope which cannot provided by a voltmeter?5 UTM(ii)With the timebase of an oscilloscope switched off an alternating voltagemoves the spot on the screen up and down once in 0.20 s. Its range ofmovement is 4.0 cm and the y-gain is set at 20 mV/cm. What is theamplitude and the frequency of the signal?5 UTMUTM& UTMWhen 10100 is input to a 5-bit digital-to-analog converter, the output(c) (i)5 UTM* UTMcurrent is 10 mA. What will be the output current if the input is 11101?(ii) Sketch the output versus input graph_for a 4-bit digital-to-analogUTM1 V. Your sketch must clearly indicate the resolution of the DAC.UTMconverter (DAC) which has a range from 0 V to 15 V and a resolution ofUTM(iii) An analog-to-digital converter inputs a voltage ranging from 0 to 5 voltsDC and converts the voltage into an 8-bit binary number. Determine thediscrete steps in the output when the converter circuit resolves the inputvoltage from one end of its range (0 volts) to the other (5 volts)?TMUTM & ỦUTMUTMUTM5 UTM

Answered: Image /qna-images/answer/fb9e1284-508b-48c8-a125-1de6b47d68b2.jpg

(b) (i) Although both voltmeter and oscilloscope can measure voltages, however an oscilloscope can provide more information on voltages compared to the voltmeter. What are the information that can be provided by an oscilloscope which cannot provided by a voltmeter? 5 UTM (ii) With the timebase of an oscilloscope switched off an alternating voltage TM moves the spot on the screen up and down once in 0.20 s. Its range of movement is 4.0 cm and the y-gain is set at 20 mV/cm. What is the amplitude and the frequency of the signal? UTM * UTM

(b) (i) Although both voltmeter and oscilloscope can measure voltages, however an oscilloscope can provide more information on voltages compared to the voltmeter. What are the information that can be provided by an oscilloscope which cannot provided by a voltmeter? 5 UTM (ii) With the timebase of an oscilloscope switched off an alternating voltage TM moves the spot on the screen up and down once in 0.20 s. Its range of movement is 4.0 cm and the y-gain is set at 20 mV/cm. What is the amplitude and the frequency of the signal? UTM * UTM

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter9: Measuring Instruments

Section: Chapter Questions

Problem 13RQ: 13. A waveform shown on the display of an oscilloscope completes one cycle in 50 . What is the...

See similar textbooks

Similar questions

The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 1 V/cm. Determine the (i) amplitude of waveform Q (i) peak to peak value of waveform P. (ii)i frquency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. () Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (ii) Frequency of waveform P = (iv) Phase angle difference between P and Q in Degrees =
The main purpose of an oscilloscope is to graph an electrical signal as it varies over time. Most scopes produce a two-dimensional graph with time on the x-axis and voltage on the y-axis. The voltage waveform on the screen looks as shown in the figure below. Here, the vertical resolution of the oscilloscope is set up to be 2 mV/division and the horizontal resolution is 2 ms/division. Time 1. Determine the peak-to-peak amplitude of the wave. Voltage
3. A sinusoidal waveform displayed on an oscilloscope is shown in Figure 2. The 'time/cm' switch is on 10 ms and the 'volts/cm' switch is on 5V/cm. Determine for the waveform: a) The frequency of both waveforms b) The peak-to-peak value of waveform Q c) The amplitude of waveform P Figure 2
V₁ 12 In the figure shown, what is the peak to peak voltage of V1 if the vertical sensitivity of the oscilloscope is 0.25 V/Div* HIPNHHHH ALL
The wavelorm displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 50 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (1) amplitude of waveform Q, (ii) peak to peak value of waveform P, (111) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. 主 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P (iii) Frequency of waveform P =
The waveform displayed on an oscilloscope is as shown in Figure 3. The 'time/cm' switch is set to 2 ms/cm, and the 'volts/cm' switch is set to 0.5 V/cm. Determine: (i) amplitude of waveform Q (ii) peak to peak value of waveform P P (iii) frequency of waveform P (iv) angular frequency of waveform Q and (v) phase angle difference between P and Q in Degrees. 主 24°C Type here to search
What is the maximum voltage across the capacitor? (Hint: Observe from the oscilloscope graph) Function Generator Set up:Frequency = 100 Hz,Amplitude = 5 Vp [Peak voltage = 5 V i.e. Peak- peak = 10 V]Waveform = square wave Oscilloscope Set up:Time base scale: 2 ms/div(Input signal) Channel A scale: 2 V/ div(Output Signal) Channel B scale: 2V/ div
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.5 ms/cm, and the 'volts/cm' switch is set to 0.2 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees. Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. (i) Amplitude of waveform Q = (ii) Peak to peak value of waveform P = (iii) Frequency of waveform P =
Discussion 1. It is required to draw a sine wave signal of amplitude 12 volts P.P and frequency of 2 KHz on oscilloscope having voltage scale of 2 volts/cm and time base scale of 0.125 m sec / cm. Draw it on your lab paper. 2. It is required to draw a sine wave signal of amplitude 8 volts P.P and frequency of 2 KHz on ocilloscope having voltage scale of 2 volts/cm and time base scale of 0.125 u sec / cm. Draw it on your lab paper. 3. It is required to draw a sine wave signal of amplitude 4 volts P.P and frequency of 1 KHz on oscilloscope having voltage scale of 2 volts/cm and time base scale of 1 um sec / cm. Draw it on your lab paper.
Pre-Laboratory Assignment 1-) What are the basic purposes of using an oscilloscope and a multimeter? 2-) What is the difference between AC and DC coupling? 3-) What is the purpose of the trigger systemin the oscilloscope? 4-) Draw the following signals: a-) 5 sin 2n1000t b-) 3cos2n500t +3
Electrical Engineering Why/how is a small 100OHMS source resistor used to measure the phase angle of current using the oscilloscope?
Please Connect the circuit shown above in Tinkercad and measure the output voltage in oscilloscope.