Please have the solution in clear writing a- Table 1, Indicates the characteristics typical for the common guided media forlong-distance point-to-point applications. Calculate the attenuation for eachcoaxial and twisted pair cables at 1MHz.Frequency RangeTypical Attenuation Typical Delay Repeater Spacing0.2 dB/km @ 1 kHz50 µs/kmTwisted pair (withloading)Twisted pairs(multipair cables)Coaxial cableOptical fiber0 to 3.5 kHzTHz TeraHertz 10¹2 Hz0 to 1 MHz0 to 500 MHz186 to 370 THz0.7 dB/km @ 1 kHz7 dB/km @10 MHz0.2 to 0.5 dB/km5 μs/km4 μs/km5 µs/km2 km2 km1 to 9 km40 kmTable 1: Point-to-Point Transmission Characteristics of Guided Media

Attenuation can be defined as it refers back to the decline in the strength or intensity of a signal…

a- Table 1, Indicates the characteristics typical for the common guided media for long-distance point-to-point applications. Calculate the attenuation for each coaxial and twisted pair cables at 1MHz. Frequency Range Typical Attenuation Typical Delay Repeater Spacing 0 to 3.5 kHz 0.2 dB/km @ 1 kHz 50 μs/km 2 km Twisted pair (with loading) Twisted pairs (multipair cables) Coaxial cable Optical fiber THz TeraHertz = Tal 0 to 1 MHz 0 to 500 MHz 186 to 370 THz = 1012 Hz 0.7 dB/km @ 1 kHz 7 dB/km @ 10 MHz 0.2 to 0.5 dB/km 5 μs/km 4 μs/km 5 μs/km 2 km 1 to 9 km 40 km

a- Table 1, Indicates the characteristics typical for the common guided media for long-distance point-to-point applications. Calculate the attenuation for each coaxial and twisted pair cables at 1MHz. Frequency Range Typical Attenuation Typical Delay Repeater Spacing 0 to 3.5 kHz 0.2 dB/km @ 1 kHz 50 μs/km 2 km Twisted pair (with loading) Twisted pairs (multipair cables) Coaxial cable Optical fiber THz TeraHertz = Tal 0 to 1 MHz 0 to 500 MHz 186 to 370 THz = 1012 Hz 0.7 dB/km @ 1 kHz 7 dB/km @ 10 MHz 0.2 to 0.5 dB/km 5 μs/km 4 μs/km 5 μs/km 2 km 1 to 9 km 40 km

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b) If quantity A is PATAT with TC of 2mV/C, and quantity B is CTAT with TC of -1mVrC, then determine the following quantities if they are PTAT or CTAT 1. 1/A 2. 1/B 3. A+ 5°B
The corresponding R function for teh PMF is __________.
Which Transmission Line Parameter is neglected or ignored in most classifications of Transmission Line Equivalent Circuits? A. The Line Inductance B. The Line Resistance C. The Shunt Conductance D. The Shunt Capacitance
A 500MCM ACSR cable has 37 strands. Determine the diameter in mils of each strand.
Explore the concept of crosstalk and impedance mismatch in cables and how they affect signal integrity.
Propose a novel cable design that addresses specific performance or environmental requirements.
Explain the concept of cable impedance and its importance in high-frequency signal transmission. How does impedance matching affect cable performance?
Discuss the impact of cable impedance on signal quality in high-speed data transmission. How does impedance matching play a role in cable design?
a line characteristic impedance 600 ohm and 3 db loss is a half wavelength .it is fed by a source of emf 5v and impedance 1 kilo ohm and is terminated by aload 0f 400 ohms impedance .calculate the load voltage ..
Write about the uses and importance of twisted pair cable - crossover cable
In a series eaperiment with R, =1n and R, 4n across a power Supply E, the slope g (E, v, ) and of CE,V2) are re spechively (...) C ---- ) (a) 2 , 3 ( b) 5 , 1.25 (e) 2.15 , 5 (d) 3, 2
A fiber optic cable with a core diameter of 100 µm is to be spliced to a cable with a core diameter of 80 μm. Calculate the coupling loss from the unequal diameters.