(a) (ii) Following chemical species were reported for water sample from a well.Concentration (milli equivalent)/L1515053012188.8SpeciesChloride (CL)Sulphate (SO2-)Carbonate (CO2)Bicarbonte (HCO3)Calcium (Ca²+)Magnesium (Mg2+)pHFind(i)The total hardness (in mg/L) as CaCO3(ii) Alkalinity present in the water (in mg/L) as CaCO3.

Answered: Image /qna-images/answer/f8e82fca-d226-4929-80bc-8a62720e1547.jpg

(a) (ii) Following chemical species were reported for water sample from a well. Concentration (milli equivalent)/L 15 15 05 30 12 18 8.8 Species Chloride (CL) Sulphate(SO2-) Carbonate (CO3-) Bicarbonte (HCO3) Calcium (Ca²+) Magnesium (Mg2+) pH Find (i) The total hardness (in mg/L) as CaCO3 (ii) Alkalinity present in the water (in mg/L) as CaCO3.

(a) (ii) Following chemical species were reported for water sample from a well. Concentration (milli equivalent)/L 15 15 05 30 12 18 8.8 Species Chloride (CL) Sulphate(SO2-) Carbonate (CO3-) Bicarbonte (HCO3) Calcium (Ca²+) Magnesium (Mg2+) pH Find (i) The total hardness (in mg/L) as CaCO3 (ii) Alkalinity present in the water (in mg/L) as CaCO3.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 2ETSQ

See similar textbooks

Similar questions

d) Calculate total hardness in ppm of a solution of both 55 mg/L Al2(SO4)3 and 45 mg/L Mg(NO3)2.
Determine the force in each member of the loaded truss. All triangles are equilateral with side length d. The forces are positive if in tension, negative if in compression. AB= tolerance is ± 1 in the 3rd ficant digit. AG = BC = BG= CD = CF = i i i i i B i G 2.8 KN d F 6.3 KN 3 3 3 3 3 3 KN KN KN kN kN D E
Question 3: The block shown is made of a magnesium alloy for which E=760GPa and 9 =0.35. Knowing that o=157 MPa, determine (a) the magnitude of o, for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
tolerance is +-1 in the 3rd significant digit
A small amount of Mg-EDTA is often added in the titrimetric determination of water hardness. Why?
The block shown is made of a magnesium alloy for which E = 45 GPa and ν = 0.35. Knowing that σx = -180 MPa, determine (a) the magnitude of σy for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
6. The mineral analysis below was reported for a water sample. 6.0 Bicarbonate 120 as CaCO3 Ca2+ 50.0 SO?- 94.0 Mg* 20.0 pH 7.3 Na* 5.0 Note: All reported as "mg/L as the ion" unless stated otherwise. e. Draw a bar chart that includes all the ions listed above. f. What is the total hardness of the water in mg/L as CaCO3? g. What is the carbonate hardness of the water in mg/L as CaCO;? h. What is the non-carbonate hardness of the water in mg/L as CaCO3? How would you characterize this water (very soft, moderately hard, etc.)? Explain your i. answer.
Q) When Plastic viscosity is increase ? small solid concentration Concentration solid Increases solid concentration Decrease solid concentration Irregular solid concentration
I In a compression test and for a very ductile material similar to copper , the diameter and the length of the specimen before the test were 60mm and 80mm respectively . Find the length , in inches , after the test if the diameter became 120mm . Assume that the density remained unchanged
The following mineral analysis was reported for a water sample taken from a municipal groundwater water well. Determine the total, carbonate and non carbonate hardness in mg/L as CaCO3 using the predominant polyvalent cation definition of hardness. All reported as "mg/L as the ion" Iron 0.2 Manganese 0.6 Ammonium 0.5 Sodium 4.7 Potassium 0.9 Calcium 67.2 Magnesium 39 Barium 0.5 Silica 20 Flouride 0.35 Boron 0.1 Nitrate 0 Chloride 4.5 Sulfate 29 Alkalinity 284 as CaCo3 pH 7.6 units
A copper specimen subjected to the Brinell Hardness Test using hardened steel ball indenter of diameter 13 mm and the indentation diameter 3.78 mm is measured using an optical magnifying lens with a ruler. Draw the Brinell Hardness Test setup neatly and determine the force applied on the specimen. Take Brinell Hardness Number for copper as 1037. Surface Area of Indentation (in mm2) = Applied Force (in N) =