A d.c. Buck converter operates at frequency of 2000 Hz from 200 V d.c. source supplying a 5 2 resistive load. The inductive component of the load is 5 mH. For output average voltage of 100 V, find: (a) The duty cycle. (b) ton. (c) The rms value of the output current. (d) The average value of the output current.

A d.c. Buck converter operates at frequency of 2000 Hz from 200 V d.c. source supplying a 5 2 resistive load. The inductive component of the load is 5 mH. For output average voltage of 100 V, find: (a) The duty cycle. (b) ton. (c) The rms value of the output current. (d) The average value of the output current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.
RMS value.
13. The transformer in a large welder provides single-phase ac output at 30 V, 50 Hz. An SCR bridge is used to control the welder. A large inductor helps to maintain a welding arc. a. What phase delay angle should be used to set an initial voltage of 25 Vac? b. The phase angle drops back once the arc has formed. What phase delay angle is needed for 8 Vdc output?
Find the average and r.m.s. values of the a.c. voltage whose waveform is given in the figurebelow. a. Average value b. RMS value
3. A sinusoidal waveform is displayed on a c.r.o. screen. The peak-to-peak distance is 5 cm and the distance between cycles is 4 cm. The 'time'switch is on 100 µs/cm and the 'volts/cm' switch is on 10 V/cm. Determine (i) angular frequency (ii) peak (iii) rms value of voltages (iv)Time period and (v) form factor.
4) Determine the value of voltage across resistor and capacitor5) Convert in rms values
Find RMS value.
In a buck converter, what are the benefits and disadvantages if the changes of duty cycle is drastic i.e, fast system response? How about when duty cycle changes slowly i.e, slow system response?
In the given circuit, a step down transformer with an RMS voltage as 110V /11-0-11 V is used with RL = 1 KO. Assume diode as Germanium and the input frequency is F= 50HZ. D, CT Vin RL D2 1- Name the given circuit. 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms. all
Does the input power factor of convertors depend on the load power factor? why?
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9