A cylinder with a weight of 800 lb is held in equilibrium by three ropes. The hooks are arranged in acircular pattern a distance 1 ft from the origin and are all on the flat zy-plane. ₁ is the anglebetween the positive z-axis and r.BZT0₁0₁WCdiValues for the figure are given in the following table. Note the figure may not be to scale.Variable Valued₁2.5 ft1 ft125 degreesa. Determine the magnitude of the force/tension in cord A, TA.b. Determine the magnitude of the force/tension in cord B, TB.c. Determine the magnitude of the force/tension in cord C, Tc.Round your final answers to 3 significant digits/figures.The magnitude of the force/tension in cord A isThe magnitude of the force/tension in cord B isThe magnitude of the force/tension in cord C'islblblb

Answered: Image /qna-images/answer/5352dea2-ea04-4684-8631-0d329f4d852b.jpg

A cylinder with a weight of 800 lb is held in equilibrium by three ropes. The hooks are arranged in a circular pattern a distance 1 ft from the origin and are all on the flat zy-plane. ₁ is the angle between the positive z-axis and r. B T 0₁ Z 0₁ D-J W Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2.5 ft 1 ft 125 degrees di a. Determine the magnitude of the force/tension in cord A, TA. h.d. JD m

A cylinder with a weight of 800 lb is held in equilibrium by three ropes. The hooks are arranged in a circular pattern a distance 1 ft from the origin and are all on the flat zy-plane. ₁ is the angle between the positive z-axis and r. B T 0₁ Z 0₁ D-J W Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2.5 ft 1 ft 125 degrees di a. Determine the magnitude of the force/tension in cord A, TA. h.d. JD m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cables AB and AC are acting on the pole with forces FAB=540N and FAC=560N with parameters defining the attachment points shown in the table. We want to write the vector FAB in cartesian vector form. Уг parameters value units 540 560 5.5 FAB FAC L 71 4/₁ 72 4/2 →→ FAB= 281.88 3.5 Submit Question 4 N N m m m m m FAC A write the vector FAB in Cartensian Vector Notation. Round your final answers to 3 significant figures. xi +247.10 Y₁ Z AB B +-388.26 x N
Current Attempt in Progress The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 16 mm d = 100 mm t = 9.6 mm Additionally: • The area of each pipe is A = 2726 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz=245460000 mm4. If the beam will be subjected to a shear force of V = 275 kN, determine the shear stress at point K, located at yk = 70 mm below the z centroidal axis. H K X Z Ун Ук H ↑ K 31 h
The bear cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw - 14 mm d = 100 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1436 mm². • The moment of inertia of the entire bear cross section about the z centroidal axis is lz=140920000 mm². If the bearn will be subjected to a shear force of V = 170 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, T. S 65MPA and the angle of rotation of the free end limited to 11°. Use GS 84 GPa and Ga = 27 GPa. %3D %3D 75 mm Aluminum Steel 50 mm 2 m 1.5 m
Using the Portal Method determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 10 m P= 116 kN ЗР/2 G H 4m P 5m a b
Consider the cross section shown in (Figure 1). Suppose that b = 112 mm Part A Determine the major principal moment of inertia Imar of the cross section about the principal axis having an origin at point C. Express your answer to three significant figures and include the appropriate units. ? Imax = Value Units Submit Request Answer Part B Determine the angle 0,, as measured on the cross-section from the positive z axis. Figure Express your answer using three significant figures. Enter positive value if the angle is counterclockwise and negative value if the angle is clockwise. Vol AEO vec ? 10 mm - Op, = 80 mm Submit Request Answer 80 mm. 10 mm Part C 10 mm - Determine the minor principal moment of inertia Imin of the cross section about the principal axis having an origin at point C.
EXAMPLE (2) A bar of uniform cross sectional area 100mm2 is subjected to forces as shown in Fig. Calculate change in length of the bar . Take E=2*10' N/mm'. A B D IkN SKN +6KN 2kN 300mm 400mm 600mm
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the depth of the neutral axis of the section in PART A in mm.0
A steel shaft is fixed at its one end as shown in figure find and maximum. G=84GPa :Total angle of rotation (1 :Shear stress at member AB (2 BC :CD 5mm 125N.m 500N.mm/mm 50mm 5mm D 125mm 125mm B 250mm A 50mm
QUESTION 4 The assembly consists of three titanium (E is 120 GPa) rods and a rigid bar AC. The cross sectional area of each rod is given in the figure. If force of 30 kN is applied to the ring F, determine the horizontal displacement of point F. 1.2 m AcD = 600 mm² %3D 0.6 m 03m E 30 kN 0.3 m AEF = 1200 mm? A AB= = 900 mm2 1.8 m
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm tw = 14 mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 325870000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.