A column is constructed from high strength concrete reinforced with 8 A992 steel rods. The column has diameter d₁= 7.5 in. and the steel rods have diameter d₂ = 0.75 in. If an axial load of P = 180 kip is applied, calculate the magnitude of the resulting average normal stress in the concrete and in the steel rods. Hint: The displacement of the concrete must be the same as that of the steel. d₁ d₂ ✓ @000 BY NO SA 2021 Cathy Zupke The magnitude of the average normal stress in the steel rods is a steel = ksi. The magnitude of the average normal stress in the concrete is o concrete ksi.

A column is constructed from high strength concrete reinforced with 8 A992 steel rods. The column has diameter d₁= 7.5 in. and the steel rods have diameter d₂ = 0.75 in. If an axial load of P = 180 kip is applied, calculate the magnitude of the resulting average normal stress in the concrete and in the steel rods. Hint: The displacement of the concrete must be the same as that of the steel. d₁ d₂ ✓ @000 BY NO SA 2021 Cathy Zupke The magnitude of the average normal stress in the steel rods is a steel = ksi. The magnitude of the average normal stress in the concrete is o concrete ksi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.9P: Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see...

See similar textbooks

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see figure). The structural core of the tower is a circular cylinder of height ft, outer diameter d2, and inner diameter d1.For simplicity in the analysis, assume that the weight of the tower is uniformly distributed along the height. Obtain a formula for the maximum permissible angle a if there is to be no tensile stress in the tower.
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. The column is separated from the concrete foundation by a square bearing plate with the dimension of 160 mm x 160 mm. The working compressive and tensile stresses are 180 MPa and 200 MPa respectively, while the working bearing stress of concrete is 10 MPa. Find the largest force P that can be applied to the column. Sleel Concrete Foundation Bearing Plane
A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b = 250 mm and d = 400 mm, determine the stresses in the steel and concrete if the axial compressive load to be supported by the column is 400 kN. For steel, Est = 200 GPa; for concrete, Eco = 15 GPa. 6 - 20 mm steel bars 4 m d
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
Determine the stress components acting on the inclined plane AB in if: normal stressy = 61MPa shear stressxy = -25 MPa solve the problem using the method of equilibrium. Find normal stress x' =? find shear stress x'y' =? I have a question regarding the answer you provided. The shear stress is -25MPa. You used a positive 25MPa in the solution. Why is that?
The masonry pier is subjected to the FFF = 810 kNkN load. Consider xx = 0.25 mm and yy = 0.5 mm. Neglect the weight of the pier. Determine the normal stress at corner A. Determine the normal stress at corner B. Determine the normal stress at corner C.
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.