A 750 kVA, 11 kV/ 400 V with 5% impedance distribution transformer is to beinstalled in an industrial power network to serve the industrial motor pump asdepicted in Figure Q3.(i) Analyse the short circuit capacity of the transformer (in kVA)(ii) Investigate the voltage variation (in percentage) during the motor starting(iii) Recommend a proper size of the transformer if the voltage variation duringthe motor starting is to be limited to a maximum value of 8%Infinite sourceStandard rating (in kVA):150, 250, 300, 400, 500,630, 750, 1,000, 1,250,1,600, 2,000, 2,5003750 kVA11kV/400VHorse Power = 500 HPPF = 0.8 lagging, Efficiency = 70%Starting inrush current = 6 times

Given the 750 KVA , 11kv/400v with 5% Standard rating in KVA given 150, 250, 300, 400, 500, 630,…

A 750 kVA, 11 kV/ 400 V with 5% impedance distribution transformer is to be installed in an industrial power network to serve the industrial motor pump as depicted in Figure Q3. (1) Analyse the short circuit capacity of the transformer (in KVA) (i) Investigate the voltage variation (in percentage) during the motor starting (ii) Recommend a proper size of the transformer if the voltage variation during the motor starting is to be limited to a maximum value of 8% Infinite source Standard rating (in kVA): 150, 250, 300, 400, 500, 630, 750, 1,000, 1,250, 1,600, 2,000, 2,500 750 KVA 11kV/400V Horse Power = 500 HP MPF = 0.8 lagging, Efficiency = 70% Starting inrush current = 6 times

A 750 kVA, 11 kV/ 400 V with 5% impedance distribution transformer is to be installed in an industrial power network to serve the industrial motor pump as depicted in Figure Q3. (1) Analyse the short circuit capacity of the transformer (in KVA) (i) Investigate the voltage variation (in percentage) during the motor starting (ii) Recommend a proper size of the transformer if the voltage variation during the motor starting is to be limited to a maximum value of 8% Infinite source Standard rating (in kVA): 150, 250, 300, 400, 500, 630, 750, 1,000, 1,250, 1,600, 2,000, 2,500 750 KVA 11kV/400V Horse Power = 500 HP MPF = 0.8 lagging, Efficiency = 70% Starting inrush current = 6 times

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: If both transformers are connected in parallel to supply a load (1.2 + j 2.3) ohm, find the output power of each transformer.
Transformer 1) Enumerate the way/s by which the voltage of the large coil may be: a) increased (AC source) b) reduced to zero (AC source) c) increased (DC source) d) reduced to zero (DC source)
Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: The terminal voltage when transformer A is supplying half load at power factor (0.6) lagging and transformer B is supplying (85%) of full load at power factor (0.85) leading.
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.
3. An 100-KVA, 2500/125-V, 50-Hz, step-down transformer has the following parameters: R₁ = 1.50, X₁ = 2.8 2. : R₂ = 15 m , : X₂ = 20m2,: Re - 3k, and: Xm 5 KQ. The transformer delivers 85% of the rated load at a terminal voltage of 110 V and a power factor of 0.866 lagging. Use the approximate circuit referred to as the primary. a. Determine the efficiency of the transformer. b. And the voltage regulation T
Flag this question for future reference What is the test that can be conducted in the laboratory to understand the transformer impedance drops are dependent on the load current with a variation in the secondary voltage? O a. Direct Load Test O b. Open Circuit Test OC. Voltage Ratio Test O d. Polarity Test
Figure 5 shows the core of a Linear Variable Differential Transformer (LVDT). S, S2 CORE Figure 5 Explain what happens when the core is at its maximum left, null and maximum right positions.
Draw the general diagram of a single-phase transformer and briefly show how it works.
Determine the regulation of a transformer in which thepercentage resistance drop is 1% and the percentagereactance drop is 5% when the power factor 0.8 leading.
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
Q Two transformers A and B have the following data Transformer A: 6600/440 V, (250 KVA ) requires ( 6%) of rated voltage to circulate (90%) of full load current at power factor (0.25) when the low voltage winding is short circuited and the no load loss is equal to (2500 W). Transformer B: 6600/420 V, (600 KVA) requires (9%) of rated voltage to circulate (80%) of full load current at power factor (0.16) when low voltage winding is short circuited and no load loss is equal to (4500 W). Calculate the followings: The maximum efficiency of each transformer at power factor (0.75) lagging.