A 4.16 kV, 3-ph industrial plant bus is supplied from the utility mains. Connected to the 4.16 kV plant bus are the following three-phase loads: 1. 2. A 1750 hp induction motor bank operating at 80% full-load, 0.86 pf lagging and 94% efficiency .A 1000 hp synchronous motor operating at 65% full-load and 93% efficiency. The synchronous motor has negligible armature resistance and synchronous reactance of 3002/phase Questions: a. Draw a single-line schematic diagram to illustrate the scenario described above. Show all P and Q flows. Determine the real and reactive power of the induction motor Determine the apparent power and power factor of the synchronous motor if it is overexcited to correct the overall plant power factor to 0.97 lagging. Show all work. b. c.

A 4.16 kV, 3-ph industrial plant bus is supplied from the utility mains. Connected to the 4.16 kV plant bus are the following three-phase loads: 1. 2. A 1750 hp induction motor bank operating at 80% full-load, 0.86 pf lagging and 94% efficiency .A 1000 hp synchronous motor operating at 65% full-load and 93% efficiency. The synchronous motor has negligible armature resistance and synchronous reactance of 3002/phase Questions: a. Draw a single-line schematic diagram to illustrate the scenario described above. Show all P and Q flows. Determine the real and reactive power of the induction motor Determine the apparent power and power factor of the synchronous motor if it is overexcited to correct the overall plant power factor to 0.97 lagging. Show all work. b. c.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer with step by step math for Zin, Zout, and the load voltage. Thank you!
Q2 (a) Outline with the aid of a suitable diagram the necessary power conversion stages required to interface a small permanent magnet (PM) wind generator to a 3 phase AC grid. (b) Given the operating conditions for a stand alone star connected 3 phase synchronous generator outlined in Table Q2b construct a scaled phasor diagram and determine the resultant load current and power factor. On the same phasor diagram indicate the resultant changes when the load current increases by approximately 20% for no change in (lagging) power factor or excitation voltage. Value Parameter V. 415V Excitation Voltage Load Angle 300V 20° Xs 1.50 Table Q2b A star connected 3 phase wound field synchronous generator with a synchronous reactance of 120 is connected to a 11kV (line) grid and supplies 1MW at 0.92 lagging power factor at its terminals. Calculate the phase current and resultant voltage across the synchronous reactance (Vxs), and from a scaled phasor diagram graphically determine the required…
A 6 kV , 1000 kVA , 3-ph alternator is delivering full-load at 0.8 lagging. Its reactance is 20% and resistance negligible. By changing the excitation, the e.m.f. is increased by 25% at this load. Calculate the new current and power factor. The machine is connected to infinite bus-bars.
Q) A P-Pole three-phase induction machine with spatial distribution of stator windings is assumed to be sinusoidal A) It is desirable to express the Xs (0m) function for each phase in terms of conductor/radian B) It is desirable to calculate Tag(t,Oe), each phase
. A 20 kW compound generator works on full load with terminal voltage of 250 V. The armature, series, and shunt windings have resistances of 0.05-ohm, 0.025 ohm, and 100 ohms, respectively. If the machine is connected short shunt, the emf generated is nearest to. (Our subject is Electrical Machines 1 ) (I need a clear answer and solution. Thank you so much)
Refer here for the specifications of the D400. a) What power output should you be able to supply from the 24V D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will the output power be? c) According to the performance graph what is the maximum power you can obtain from the 24V D400? There is a possibility of installing the turbine on top of a 20m high mast instead. Assuming that Zo=0.012, what would you expect the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m.
Two 50-MVA, 3-phase alternators operate in parallel. The settings of the governors are such that the rise in speed from full-load to no-load is 2 percent in one machine and 3 percent in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 100 MW, what would be the load on each machine when the total load is 60 MW? (Req'd) Draw an appropriate diagram.
(Q1f, Draw and compare the per-phase electrical equivalent circuits of a transformer and of an induction motor. Using simple magnetic circuits, explain how the values of the magnetising (shunt) impedances compare in the two devices and what is the cause of the difference between the two? Figure 2. A transformer and an induction motor. Among other differences, one is typically rectangular, and the other one is round :D
A DC series generator is supplying a current of 5A to a series lighting system through a feeder ofto total resistance, 1.0 ohm. The terminal voltage is 2500 V. The armature and series fieldresistances are respectively 18 and 15 ohms respectively. A 30-ohm diverter resistance isshunted across the series field. Determine the power developed in the armature of thegenerator?
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www Ish1 Rh1 a.350-360 V b.450-460 V c. 550-560V Rat www az G₂ Raz 5000 A Ish2
A balanced three phase induction motor has an efficiency of 0.85 when its output is 44.76 kW. At this load both the stator copper loss and the rotor copper loss are equal to the core losses. The mechanical losses are one-fourth of the no-load loss. Calculate the slip. [4.94%] (AMIE Sec. B Elect. Machines (E-3) Winter 1991)