6-11. Draw the influence lines for (a) the vertical reaction at B, and (b) the moment at E. Assume the supports at B and D are rollers. There is a short link at C. Solve this problem using the basic method of Sec. 6-1. *6-12. Solve Prob. 6-11 using the Müller-Breslau principle. AD E IB -10 ft 10 ft 15 ft- C -15 ft-

6-11. Draw the influence lines for (a) the vertical reaction at B, and (b) the moment at E. Assume the supports at B and D are rollers. There is a short link at C. Solve this problem using the basic method of Sec. 6-1. *6-12. Solve Prob. 6-11 using the Müller-Breslau principle. AD E IB -10 ft 10 ft 15 ft- C -15 ft-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the influence line for vertical reaction at support B, shear at C and the moment at point D of the beams shown. From the influence line of By, what is the value of By when x = 0 m due to a unit load? Use four decimal places. A B |--sm- -5 m- -8 m- C -8 m- D -5 m- E
The geometry of the compound beam is given below. Sketch the qualitative influence line for the support reactions at Á, B and D. Sketch as well the qualitative influence line for the shear and moment at E. Take note that C is an internal pin. A E OD -2 m- -2 m- 1 m 3 m-
1. Draw the influence line for member FC. Use the tabulation method. 2. A uniform live load of 10kn/m and a single live concentrated force of 35kn are to be placed on the beam. The beam has a weight of 38kn/m. Determine (a) the maximum vertical reaction at support B, and (b) the maximum negative moment at point B. Assume the support at A is a pin and B is a roller.
2. Draw the influence line for the force in (a) member EH and (b) member JE. K A B C D -4 m 4 m 4 m 4 m 4 m 4 m 3 m G
6.12 Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the left of B, and (c) the momentat B. A is a pin and B is a roller. Solve using Müller-Breslau’s principle.
Solve and draw the influence line for the force in member JE.
Draw the influence line for the vertical reaction at A. Use the analytical method in solving. Assume the support at A is a pin and B is a roller. In the influence line for the vertical reaction at A, What is the maximum ordinate? What is the ordinate at C? What is the ordinate at the (a) left-most part and (b) right-most part of the beam?
Draw the influence line for positive moment at E (E is located at the center of section C-D) using the Muller Breslau Principle.
The beam is used to support a dead load of W1 N/m, alive load of W2 kN/m, and a concentrated live load of P kN.Determine (a) the maximum positive (upward) reaction at B, (b)the maximum positive moment at C, and (c) the maximumnegative shear at C. Assume B and D are pins.
3 Draw the influence line for the force in (a) member JI. (b) member IE, and (c) member EF. 68-6 6 n 6n 6n-
Construct the influence line for the shear at point C. The x in the table is from point A.
1. The beam is used to support a dead load of 0.6 k/ft, a live load of 2 k/ft and a concentrated live load of 8 k. Determine (a) the maximum positive reaction at A, (b) the maximum positive moment at C, and (c) the maximum positive shear just to the right of the support at A. Assume the support A is a pin and B is a roller. A B 10 ft- 10 ft- - 10 ft -5 ft-