5ft B 1.5ft The AB bar, whose material is Copper Hard Drawn, and the BC bar, whose material is 6061 T6 aluminum, are joined by BC collar and recessed at point A and C. If no load is there when the temperature is 50 ° F, determine the normal effort when the temperature is 40 ° F. The area of the two bars is 2.5 in².

5ft B 1.5ft The AB bar, whose material is Copper Hard Drawn, and the BC bar, whose material is 6061 T6 aluminum, are joined by BC collar and recessed at point A and C. If no load is there when the temperature is 50 ° F, determine the normal effort when the temperature is 40 ° F. The area of the two bars is 2.5 in².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

105 GPa, ab 20.9 × 10¯C) and a steel rod 200 GPa, a 11.7 × 10¯C) have the dimensions shown at a temperature of 20°C. The steel rod is cooled until it fits freely into the link. The temperature of the whole assembly is then raised to 45°C. Determine (a) the final normal stress in the steel rod, (b) the final length of the steel rod. A 5 A brass link (E, #******* 0.12 mm → #jom Jammi Brass 250 mm Steel Q Search L Lo j⠀⠀⠀⠀i A 50 mm 37.5 mm 30-mm diameter 37.5 mm Section A-A LO*·ce
The papped cantilerer beam Andye Draw SFD Bno and Eleshc casre. Consiskent defomution methed. EI b constant bm
The two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in each bolt; and (b) shearing stress at the mid- height of the upper steel plate. 150 mm 12 mm 250 mm 12 mm Solution:-
Q1// The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 150MPa and the allowable bearing stress for the wood is 28MPa. Assume that the hole in the washers has the same diameter as the bolt. -2 m- 3 kN 2 kN 1.5 kN 2 m--1.5 m-1-1.5 m-1-1.5 m--1.5 m- B D
Derive the maximum steel ratio and the recommended rteel ratio fe' O.856 fy Po-004 3 0.85 fc' pooos= 0-85
The wire AB is unstrentched when tetha = 45 degrees. If a load is applied to the bar AC, which causes tetha to become 46.7 degrees. Determine the normal strain in the wire.
Fagure O 2. A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and 30 mm internal diameter. The lube is closed at cach end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is raised by 60 "C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m and 100 GN/m and a for steel and copper as 12 10 per "C and 18 x 10" per "C. stress is the middle
•8-57. The 2-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point A, and show the results on a differential element located at this point. 8-58. The 2-in.-diameter rod is subjected to the loads shown. Determine the state of stress at point B, and show the results on a differential element located at this point. 500 lb 600 lb B 800 lb 8 in. 12 in. CO
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
11-59. The aluminum machine part is subjected to a moment of M-75 kN-m. Determine the maximum tensile and compressive bending stresses in the part. 10 mm 10 mm, 10 mm 40 mm B 20 mm 10 mm 10 mm M-75 N·m
Time left 0:16:22 (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 142 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L = 3 ft A = 0.5 in? E = 29 x 10° psi 4 ft - Aluminum P. 2 ft 2 ft-> L= 4 ft A = 0.75 in? E = 10 x 10° psi %3D