The figure shows a concept for a hand pump used for increasing oil pressure in a hydraulic line. Analytically determine the displacement of the piston as thehandle rotates 12.5° counterclockwise. Also, input the corresponding initial and final vertical position of the piston the space provided. (Use 2 decimal places forthe final answer.)5"B12°Offset12°A1.5"Initial Vertical Position of the Piston (inches) = 10.07Final Vertical Position of the Piston (inches) =8.45DISPLACEMENT (inches) = 1.62

Answered: Image /qna-images/answer/80bdf304-fd98-43b4-96b1-d213353793a7.jpg

Answered: 5" \B 6" 12° Offset

Engineering

Mechanical Engineering

5" \B 6" 12° Offset

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve for the indicated value, and graph the situation showing the solution point. The formula for measuring sound intensity in decibels D is defined by the equation D = 10 log (1) using the common (base 10) logarithm where I is the intensity of the sound in watts per square meter and Io = 10-12 is the lowest level of sound that the average person can hear. How many decibels are emitted from a jet plane with a sound intensity of 8.7. 102 watts per square meter? Round your answer to three decimal places. The jet plane emits Number decibels at 8.7. 102 watts per square meter. Select the correct graph of the situation showing the solution point. 200 D 150 100- 50 400 800 1200 1600 2000 400 800 1200 1600 2000 O O 0 200D 150- 100 50 0 200- Subr
In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e angle a at which slider B reaches the extreme right position. Write your answer in degrees but do not write the unit. 7 cm. Find the value of 7777 x. Answer: DELL
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 rad/s^2, 100 kN) For stresses, type (C) for compression and (T) for tension one space after the unit. (ex: 18.19 MPa (C), 6.88 psi (T))
A person starts walking from home and walks: 2 miles East 7 miles Southeast 6 miles South 6 miles Southwest 2 miles East This person has walked a total of miles Find the total displacement vector for this walk: If this person walked straight home, they'd have to walk miles Round your answer to at least one decimal place if needed.
Velocity. Suppose the distance travelled by a tanker ship departing from port is given implicitly by the equation 2-4st-75³-0 Where s is the distance in kilometres and it is time in seconds (s). Use implicit differentiation to calculate the velocity of the ship when s= 40 and 14 seconds. Note: Enter your solution as a decimal rounded to four (4) decimal places without units.
use the given information to answer the question. the horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions per minute (rpm)) and the cube of the diameter. if the shaft of a certain material 3 inches in diameter can transmit 45 hp at 110 rpm, what must the diameter,d, be in order to transmit 65 hp at 150 rpm? (round your answer to two decimal places.) d= inches
Question The following fiqure shows the position # 9 tigure shows the vs time attoched' to the end of a plot t of an 80mass The apring. the position is geven in meters and time in secands. The phasc angle is ? 0.4 (0.0.2427) 0.2 (0.7469, 0) (0.027.0) 04 0.6 0.8 t (s) -0.2 ( m)
Using the graphical method, find the sum of the vectors in each number. Draw your vectors on a separate sheet of paper. Scale 10 units: 1cm 1. A box was pushed with a force of 20 Newtons to the right and 40 Newtons to the left. What is the sum of these vectors?
An automobile tire is 65.0 cm in diameter. How fast (rpm) does the wheel turn on the axle when the automobile maintains a speed of 84.0 km/h? Round to two decimal places.
500 700 From the figure shown. -1875 To determine: C 1300 E 1300 a) Piston force BC b) Piston force FE c) Pin force G and J d) Pin force D and H 300 B 500 D 450 600 20 kN Draw the FBD: H 550 - all needed parts for calculation 250 Analytical solution. 3 digits behind comma. Dimensions in mm
52 What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing based on Mech-Millimeters.dwt. Draw the object shown in Figure A-1, starting with the center of the Ø3 circle at point 5,5. Draw only the object, not the dimensions and then answer the following questions: O 186794 198628 193132 171870 R1.0 TYP. 18 8 2 2 1 10
JUST DRAW THE SCHEMATIC DIAGRAM. NO NEED TO SOLVE. THANK YOU In Rizal province, one of its power plants has been thoroughly monitored for possible conversion into a wind power plant. A propeller wind turbine is to be used. Survey showed that Rizal Province at a height of 10 meters above the ground has a minimum wind speed of 7.1 miles per hour duringthe month of June and a maximum wind speed of 12.9 miles per hour during the month of January. The minimum temperature is at 75 degree Fahrenheit during the month of January and maximum temperature is at 89 degree Fahrenheit during the month of May. The existing power plant has an output of 54MW. For the proposed wind power, the power coefficient of turbine is 35% and the generator efficiency is 95%. Theimpeller diameter is assumed not to exceed 90m. Determine the following:a. Theoretical Wind Power Outputb. Electrical Power Outputc. Number of turbines to be installed