3. Tristate buffers can also be used for bi-directional bus operation. This is the ability to transmit and receive information on the same line. These circuits are called "transceivers." To make a transceiver you have to be able to have directional control of the wire so that information is able to flow in only one direction at any given time. By use of two tristate buffers operating in inverse we can control the direction of data flow. 4. Build the transceiver shown below and design a simple control system to allow data to flow in only one direction at any given time. Control

3. Tristate buffers can also be used for bi-directional bus operation. This is the ability to transmit and receive information on the same line. These circuits are called "transceivers." To make a transceiver you have to be able to have directional control of the wire so that information is able to flow in only one direction at any given time. By use of two tristate buffers operating in inverse we can control the direction of data flow. 4. Build the transceiver shown below and design a simple control system to allow data to flow in only one direction at any given time. Control

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

Choose the correct Answer: The difference in the propagation delay between the fastest and slowest pairs of the same un-twisted pair cable is called, O a. Delay Distortion O b. Propagation Speed O . Propagation Time O d. Delay Skew O e. Cross Talk
Design a synchronous counter that count 0,1,2,3,4,5,6,7,8,9,0 ... using Karnaugh map. 1 Add file
Construct an 8-to-1-line multiplexer using seven 2-to-1-line multiplexers. No other gate is allowed to use. Hint: please first draw the truth table of an 8-to- 1-line multiplexer. And then inspect the truth table to find out how to organize the seven 2-to-1-line multiplexers. The eight inputs of the 8-to-1-line multiplexer are I0 ~ 17 and the three control signals (also called selecting signals) are S2, S1, and SO. The output is F. Out Put Solutia tme c to I, 2:1 max 3 1. DAt Put F mux lic Solution time うて
In time the use of the ________ became the more desirable approach because an important parameter of the equivalent circuit was determined by the actual operating conditions rather than using a data sheet value that in some cases could be quite different. a.hybrid b.hybrid-pi c.re d.pi
Suppose you wish to increase the maximum clock frequency of the following circuit (without introducing timing violations or modifying the functional behavior of the circuit aside from introducing delay) through pipelining. Some potential locations for pipelining to be added to wires (labelled with numbers 1-10) are shown below: 1 D Q A DQ D Q 10 B D Q DQ C CLK Select all of the wires to which you would add pipeline registers. (Note, it is OK to increase the latency of the circuit, but not the functionality: for any sequence of input combinations, it should produce the same output combinations) If it is not possible, do not select any wires. 01 2 3 4 5 6 7 8 9 10 U 0 2 H
Choose the correct Answer: The difference in the propagation delay between the fastest and slowest pairs of the same un-twisted pair cable is called a. Propagation Speed b. Delay Skew С. Cross Talk d. Propagation Time e. Delay Distortion
i. What are equipments used for dynamic voltage regulation in PST2200 Simulator. ii. Why voltage regulation is important in Transmission lines? Explain. i. Voltage regulation may be negative for inductive load !!
There is a linearity error in the following relationship: 10 8. 0. 0.0 0.5 1.0 1.5 2.0 Distance in (cm) True False Resistance (kohms) 2.
the following blanks with a word or phrase: wires in a measurement circuit and a nearby mains-carrying conductor. w interferenc us source also known as electrostatic coupling, can occur between the signal s and wires in a measurement circuit and a nearby mains-carrying conductor. rom 2A type of optical sensors that can detect the presence of objects within its vicinity without any actual physical contact is called 3. A Sensa-is a device that measures a physical quantity and converts it into a signal which can be read by an observer er by an instrument. 4. The photons hitting the photovoltaic cell pass through the and are absorbed by electrons in the Hin p-doped upper layer S. The ability of an op amp to suppress common-mode signals is expressed in terms of its 6. The --- noise arises from fluctuations in the number of charge carriers. 7. The information in much the same way as the mind. - instrument are computing, manipulating, and processing 8. In variable capacitance transducer used…
A final year project student, Raphael, learns in EEE307 that an oscillator circuit with a differential output can be built using single-ended tuned amplifiers like the one shown below: VDD C₁=R4₁ - Vout VinM₁ Fig. 3.1 Single-ended tuned amplifier schematic (image adapted from B. Razavi ©2012)
1)What is a twisted pair cable?What are its two types and draw the sketch?
3. In LQR controller technique it can increase the input signal by a. Reducing diagonal elements of Q matrix b. Reducing diagonal elements of R matrix c. Increasing diagonal elements of R matrix d. Increasing diagonal elements of Q matrix Maximum solution- HAY. -LAZATIV a. Increase rise time b. Decrease rise time c. Increase settling time d. Decrease settling time None of all above trol provi problem 5. In LQR controller technique decreasing value of the element q12 in Q matrix can