2 NNN The following figure shows a tank with three discrete sensors; pressure switch, level switch, and temperature switch. The following three combinations must activate an alarm: ▪ High level with high temperature ▪ High level with high pressure Low level with high temperature and hi pressure ■ Level switch 2.1 Draw the truth table 2.2 Write the Boolean equation 2.3 Draw the electrical circuit tti Aqua Move Temperature switch NED BBBEENGE! 2000 1600 1600 1400 Pressure switch

2 NNN The following figure shows a tank with three discrete sensors; pressure switch, level switch, and temperature switch. The following three combinations must activate an alarm: ▪ High level with high temperature ▪ High level with high pressure Low level with high temperature and hi pressure ■ Level switch 2.1 Draw the truth table 2.2 Write the Boolean equation 2.3 Draw the electrical circuit tti Aqua Move Temperature switch NED BBBEENGE! 2000 1600 1600 1400 Pressure switch

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 3SQ: What do the following abbreviations stand for? a. SPST b. SPDT c. DPST d. DPDT e. NO f. NC

See similar textbooks

Similar questions

how to solve this
Make a table of values that shows all calculations with the switch on verses the switch off. Make sure you use proper nomenclature like R1...VR1…PR1… IRb…IRc…IR1…etc.
What among the given statement is true with respect to the dynamic performance of power electronics devices? A real switch needs infinite turn on time for On switching A real switch doesn't need a finite turn on time for Off switching A real switch needs a finite turn on time for On switching: A real switch needs an infinite turn on time for Off switching Ae Lr Ps Pr a
Q2/A- what are the main cases of insulator failures? B-what are type testing of insulator?
04: A/Write (True) for the correct answer and (False) for the wrong one: (select two nly) 1. 1. Coulomb's law can be defined as: the charge moved with an electrical energy over a distance can create a work. 2. 2. Electrical charge never generated unless there's an electrical force. 3. 3. The work done over any charge can act as a force.
Problem #3: The DE10-Lite board has three clocks that can be seen in the table below: Table 3-2 Pin Assignment of Clock Inputs Signal Name ADC CLK_10 FPGA Pin No. Description PIN N5 MAX10_CLK1_50 PIN_P11 MAX10 CLK2_50 PIN_N14 10 MHz clock input for ADC (Bank 3B) 50 MHz clock inputiBank 3B) 50 MHz clock inputiBank 38) VO Standard 3.3-V LVTTL 3.3-V LVTTL 3.3-V LVTTL You need a clock of 2.5 MHz for your circuit, and for that reason you are going to use a Ipm_counter as a frequency divider shown here: Parameter PM SVALUE Value LPM AVALUE LIM MOBULUS LPM DRCTIN LPM WIDTH LPM_PORT UPOOWN LPM_COUNTER ell If the input boardClock is connected to PIN_N5, find (a) LPM_MODULUS and (b) the minimum width of q[..] LPM_WIDTH. (c) What bit of q[..] you will pick as your 2.5-MHz clock?
Q3. A door sensor is connected to P0.5 pin, an LED to P1.5 pin and a buzzer to P2.5 pin. Write an 8051 C program to monitor the door sensor such that when it is opened, the LED will blink and the buzzer will sound every 500ms, otherwise, when the door is closed, both of the LED and buzzer will be OFF.
In FET, An outward-pointing arrow represents ___. Choose the correct answer below: a.N-type substrate b.intrinsic substrate c.P-type substrate d.extrinsic substrate
For Fixed Bias Configuration Solve for Ib, Ic and le. Atleast 2 decimal place. Be mindful of units. Assume Ic is not equal to le. ... 4 RC 15002 RB VCC 20V 90A/A 100k2 Ib=Blank 1 HA Ic=Blank 2mA le=Blank 3 mA Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer
I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would like to connect that track to an ESP-WROOM-32 board that should flash an LED whenever the track detects a non-moving train. Please list all the components (and how many of each) needed. Also, what’s the procedure for connecting the components?
Calculate the value of Xc for the circuit. Please show work. I will give you a thumbs up.
In the figure below Power Processor Input Output bag of Stop/Start Select one: a. O C. Motor O d. b. None of the choices e. Communication Power Input Output to ang On/Off control The presence of a processor module defines which rack is a local rack The yellow block represents a local rack Hopper The absence of a processor module defines which rack is a local rack The grey block represents a remote rack