2) A potter's wheel is uniform circular disk of mass 45.00kg and radius 0.450m. A electric motor brings wheel from rest to 70.00rev/min. a) What is the moment of inertia of the potter's wheel? b) How much work is done by the motor? c) If constant torque is acting on the wheel is 9.20N.m, how many revolution does it make?

2) A potter's wheel is uniform circular disk of mass 45.00kg and radius 0.450m. A electric motor brings wheel from rest to 70.00rev/min. a) What is the moment of inertia of the potter's wheel? b) How much work is done by the motor? c) If constant torque is acting on the wheel is 9.20N.m, how many revolution does it make?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 84AP: A proton is accelerated in a cyclotron to 5.0106m/s in 0.01 s. The proton follows a circular path....

See similar textbooks

Similar questions

The axis of Earth makes a 23.5 angle with a direction perpendicular to the plane of Earth’s orbit. As shown below, this axis precesses, making one complete rotation in 25,780 y. (a) Calculate the change in angular momentum in half this time. (b) What is the average torque producing this change in angular momentum? (c) If this torque were created by a pair of forces acting at the most effective point on the equator, what would the magnitude of each force be?
A bug of mass 0.020 kg is at rest on the edge of a solid cylindrical disk (M=0.10kg,R=0.10m) rotating in a horizontal plane around the vertical axis through its center. The disk is rotating at 10.0 rad/s. The bug crawls to the center of the disk. (a) What is the new angular velocity of the disk? (b) What is the change in the kinetic energy of the system? (c) If the bug crawls back to the outer edge of the disk, what is the angular velocity of the disk then? (d) What is the new kinetic energy of the system? (e) What is the cause of the increase and decrease of kinetic energy?
A proton is accelerated in a cyclotron to 5.0106m/s in 0.01 s. The proton follows a circular path. If the radius of the cyclotron is 0.5 km, (a) What is the angular momentum of the proton about the center at its maximum speed? (b) What is the torque on the proton about the center as it accelerates to maximum speed?
During a 6.0-s time interval, a fly-wheel with a constant angular acceleration turns through 500 radians that acquire an angular velocity of 100 rad/s. (a) What is the angular velocity at the beginning of the 6.0 s? (b) What is the angular acceleration of the fly-wheel?
A cylinder with rotational inertia I1=2.0kgm2 rotates clockwise about a vertical axis through its center with angular speed 1=5.0rad/s . A second cylinder with rotational inertia I2=1.0kgm2 rotates counterclockwise about the same axis with angular speed 2=8.0rad/s . If the cylinders couple so they have the same rotational axis what is the angular speed of the combination? What percentage of the original kinetic energy is lost to friction?
The centrifuge at NASA Ames Research Center has a radius of 8.8 m and can produce farces on its payload of 20 gs or 20 times the force of gravity on Earth. (a) What is the angular momentum of a 20-kg payload that experiences 10 gs in the centrifuge? (b) If the driver motor was turned off in (a) and the payload lost 10 kg, what would be its new spin rate, taking into account there are no frictional forces present?
A long, thin rod of mass m = 5.00 kg and length = 1.20 m rotates around an axis perpendicular to the rod with an angularspeed of 3.00 rad/s. a. What is the angular momentum of therod if the axis passes through the rods midpoint? b. What is theangular momentum of the rod if the axis passes through a pointhalfway between its midpoint and its end?
A bicyclist is testing a new racing bike on a circular track ofradius 53.0 m. The bicyclist is able to maintain a constant speedof 24.0 m/s throughout the test run. a. What is the angularspeed of the bike? b. What are the magnitude and direction ofthe bikes acceleration?
The blades of a wind turbine are 30 m in length and rotate at a maximum rotation rate of 20 rev/min. (a) If the blades are 6000 kg each and the rotor assembly has three blades, calculate the angular momentum of the turbine at this rotation rate. (b) What Is the torque require to rotate the blades up to the maximum rotation rate in 5 minutes?
A small ball of mass 0.50 kg is attached by a massless sting to a vertical rod that Is spinning as shown below. When the rod has an angular velocity of 6.0 rad/s, the sting makes an angle of 30 with respect to the vertical. (a) If the angular velocity is increased to 10.0 rad/s, what is the new angle of the string? (b) Calculate the initial and final angular momenta of the ball. (c) Can the rod spin fast enough so that the ball is horizontal?
A gyroscope slows from an initial rate of 32.0 rad/s at a rate of 0.700 rad/s2. (a) How long does it take to come to rest? (b) How many revolutions does it make before stopping?
Consider two objects with m1 m2 connected by a light string that passes over a pulley having a moment of inertia of I about its axis of rotation as shown in Figure P10.44. The string does not slip on the pulley or stretch. The pulley turns without friction. The two objects are released from rest separated by a vertical distance 2h. (a) Use the principle of conservation of energy to find the translational speeds of the objects as they pass each other. (b) Find the angular speed of the pulley at this time.