1.9 kg of austenite containing 1.50 Wt% C is cooled from 1200 degrees C to a temperature just below the eutectoid line.   1.  What is the proeutectoid phase? 2. How many kilograms each of total ferrite and comentite form?   3.  How many kilograms each of pearlite and the proeutectoid phase form?

Q: omenclature 2 composition, 3 crystal structure 4 Phase Diagrams,

A: Spheroidal graphite iron, also referred to as ductile cast iron, nodular cast iron, SG iron, and…

Q: For a 99.64 wt% Fe-0.36 wt% C steel at a temperature right below the eutectoid,  a) the phase…

A: The weight % of carbon, The weight % of carbon at the eutectoid point, The weight % of ferrite,…

Q: Consider 4 Kg of a 98.70 wt % Fe, 1.30 wt % C alloy at temperature just below eutectoid, determine…

A:

Q: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F) (d) What is…

A: Solution:  Given: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C…

Q: What is the maximum amount of Pb (in %) with which Sn may be alloyed to render a single β phase at…

A:

Q: For a 64 wt% Zn-36 wt% Cu alloy, make schematic sketches of the microstructure that would be…

A:

Q: A 95cu-5AG copper-silver alloy is cooled slowly from 1100°C to 20°C. What phases at what…

A:

Q: 1)  Give a brief explanation why the solubility of C is higher in y-iron than in alpha-iron

A: Gamma iron is a type of iron that has a Face-centered-cubic structure and is stable between the…

Q: which one harder pearlite producing by normalizing or by and annealing and why?

A: To change the mechanical property of the material, the heat treatment processes are employed. There…

Q: ead-tin (Pb-Sn) is an eutectic type of phase diagram. At 183 °C, liquid (61.9 wt.% Sn), solid tin…

A:

Q: b) Indicate corresponding cooling rates ( fast, mid-range, slow) and heat treatment c) Indicate a…

A:

Q: b) When this furnace-cooled AISI 1040 steel reaches room temperature, identify 1) the phase(s)…

A: Solution: Given Data:

Q: For a 50-50 Mg-Pb alloy, what would the percent of each phase be at 500°C, 300°C and 100°C?

A: Consider the diagram as shown below   Given compositions by weight are as,

Q: If a eutectoid steel sample is heated to 800°C and then quenched in a cold-water bath then what…

A: all the details are mentioned in the diagram below.

Q: Figure below is a binary eutectic copper-silver phase diagram. Consider if 500 grams of an 88 wt%…

A:

Q: Consiuer the given Al-Cu phase diagram. How much a-phase is present in an alloy with composition C,…

A: Consider the diagram shown below for the given system.

Q: Draw Iron - Iron Carbide Phase diagram and show the following: 1- Temperature, phases and carbon…

A: As per the guideline only first 3 sub-parts should be answered.

Q: What is the proeutectoid phase for an iron-carbon alloy in which the mass fractions of total ferrite…

A: Given data The mass fraction of the total ferrite is 0.90 The mass fraction of the total cementite…

Q: Draw the iron-Fe3C phase diagram. Consider high carbon steel alloy.(min carbon content 0.9C%) a) It…

A:

Q: 1.50% Pearlite, 50% Tempered Martensite 2.50% Bainite, 45% Martensite, 5% Austenite

A: To find: Steps to attain the following phase

Q: Draw the iron carbon phase diagram and labeling all lines and areas. Then:- 1- find the melting…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Suppose you wanted to have two samples of NiTi wire: one that is in the high-temperature austenite…

A: The high-temperature phase at 0 °C of the NiTi alloy is termed as Austenite. It tends to transform…

Q: The following questions are based on a high carbon steel with a composition of 1,5% C and 98,5% Fe.…

A: Given data:-105 w %C 98.5  w%FeC0=1.5 w%c

Q: For a 70-30 Zn-Cu alloy, what would the percent of each phase be at 800°C and 500°C?

A: Draw the phase diagram of Zn-Cu alloy as shown below –

Q: Abul Khair (AKS) steel industry produced steel sample (austenite phase) which has 1.4% C for some…

A: As From the Iron -Carbon Diagram we had concluded that ***As per our company policy we are supposed…

Q: 1-Identify all phases are present in the diagram. 2-Calculate the percentage of alloy components…

A:

Q: Temperature C For the phase diagram shown calculate the amount of austenite present at the point P…

A: For solution refer below images.

Q: 7- Precipitates are Two dimensions in nanoscale Nanoparticles true

A: 7. False precipitates are three dimensions in nanoscale. 8. Reinforcing phase Reinforcing phase…

Q: Consider 1.2 kg of a 99.6 wt% Fe-0.4 wt% C alloy that is cooled to a temperature just below the…

A:

Q: Consider 4.7 kg of austenite containing 0.26 wt% C, cooled to below 727°C (1341'F). (a) What is the…

A: Givenmass of austenite =4.7gcarbon =0.26%Ccooled to below 727oC 1341oF

Q: (d) Explain how a cored structure is produced in a 70% Cu-30% Ni alloy. How can the cored structure…

A: If rapid cooling is done near the boundary portion, it get solidified rapidly and that's why the…

Q: Discuss the following transformation in TTT diagram at eutectoid composition with their…

A: TTT diagrams are the short form of time-temperature-transformation diagrams which are the plot of…

Q: 2. For a 10-90 Cu-Zn alloy, what would the percent of each phase be at 500°C, 400°C and 300°C?

A:

Q: During a quenching process on a TTT diagram, we can transform pearlite into bainite. True or false?

A: In a quenching process represented on the TTT diagram, transformation is shown from austenite to…

Q: HOME WORK Calculate the amounts of solid phases of ferrite and cementite present in pearlite. y+…

A: Given dataTo determine the solid phases of ferrite and cementite present in pearlite

Q: A hypo-eutectoid steel with composition of 0.5% carbon is heated to 1000°. Using the a iron-carbon…

A: The percentage of carbon in alloy = 0.5% The temperature of heating of alloy, T = 1000 C

Q: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F).…

A:

Q: HOME WORK Calculate the amounts of solid phases of ferrite and cementite present in pearlite. y+…

A: Amount of solid phase of ferrite=6.70-0.766.70-0.022 =0.88948

Q: Question 1. (a) Why is the Fe-Fe,C phase diagram a metastable phase diagram instead of a true…

A: (a) In the Iron-Iron Carbide diagram, the Iron Carbide (Fe3C) is a unstable compound. It decomposes…

Q: Discuss the following transformation in TTT diagram at eutectoid composition with their…

A: Note: “Since you have posted a question with multiple sub-parts, we will solve first three sub parts…

Q: 1) Draw the iron-Fe;C phase diagram. Consider 0.25 and 1.1 wt% C steel alloy. It is cooled slowly…

A: