1. A line is recorded as Am long. It is measured with a (E÷200)kg tape (Bm full tape length) which is (B+0.005)m. long at 20°C under a 50 Newton pull supported at both ends. During measurement, the temperature is 10°C and the tape is suspended under 75 Newton pull. The line is measured 2.5% grade. E = 200 GPa, cross-sectional area of tape is (D÷100)cm² and the coefficient of linear expansion is 0.0000116 m/°C.

1. A line is recorded as Am long. It is measured with a (E÷200)kg tape (Bm full tape length) which is (B+0.005)m. long at 20°C under a 50 Newton pull supported at both ends. During measurement, the temperature is 10°C and the tape is suspended under 75 Newton pull. The line is measured 2.5% grade. E = 200 GPa, cross-sectional area of tape is (D÷100)cm² and the coefficient of linear expansion is 0.0000116 m/°C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2. What is the minixim vahe of thickness that can used. Use the inforamtion proviled in the table bekw. (30 Mark) P.(MPa) 6, (MPa) T, (MPa) D (m) SL (mm) S (mm) (mm) (mm) 1.3 14 12 60 30 1.4 90 16
check both LFRD and ASD. please check the given in the figure use it
b. Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
(40 Hiw A Pismatic steel bar ofa Square cross section (loo*lo0)mm is looled by Comressive force P= 1300 kU, the bar has length 2.5 m, Eg=200 G Pa, V=0.3,determine the Shortening d, the increase in the dimensions of cross Section , the change in Volume DV of the bar? loomm Joomm
In figure shown below B 960 Imm 640 N 3 280 mm 960 N a. Determine the tension in segment AC b. Determine the tensibn in segment BC
a. Calculate "P" in KN considering tension failure on gross area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Q2: Determine the resultant about the point O of the four forces and one couple which act on the plate shown in the Figure below. Note for the resultantot fore es, you 30N 5 m- should compute the magnitudo $K direchion 25N 45 2 m 70 N.M 2 m ZON 1 m 40N 30 Pagel
Q1. Find: (a) the stress in the Steel and Aluminium rods after the loap P applied and the temprature raised 60 C° and (b) the displacement under the load P. Using the data in the Table below. (30 Mark) Rod A (mm') a (µm/m. Cº) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 11.2 190 44 Aluminium 350 18.9 35 85 Aluminium A Steel 4m d + 2m P
A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the beam if the working stress in bending is 15 MPa. w = 3 kN/m 5kN Cross-section 1kN.m b 1m Upload 250mm Choose a File 1m E 2m
A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 20°C under a 50 N pull supported at both ends. During measurement, the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured on 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm? and the coefficient of linear expansion is 0.000016 m/ºC. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson
130 N A 30 mm C Determine also: a) Force at A b) Force at B c) Force at C В D -40 mm- -60 mm Analytical solution, two digits behind comma.