Q: The pharmacist attempts to weigh 120 mg of codeine sulfate on a balance with a sensitivity…
A: Maximum weight of codeine sulfate (required) =(120+6)mg=126mg
Q: The scatter of replicate measurements may be expressed by: Accuracy 2. O Standard deviation 1. 3. O…
A: When we obtain data which is highly scattered, the analytical tool we can use standard deviation.
Q: Determine the molar concentration of food dye in the sample
A: We are given absorbance of analyzed sample to be 0.349 we have to find molar concentration
Q: A. Standardization of Sodium Hydroxide (NaOH) Solution 3 Trial 1 126.2 125.7 512 264mL Trial 2 Trial…
A: #B: analysis of an unknown acid: We have to use the molarity of the standardized NaOH obtained in…
Q: The pharmacist attempts to weigh 80mg of sodium carbonate on a balance having a sensitivity…
A: Maximum weight which can be given is computed as: Maximum weight measured = Actual weight +…
Q: Actual volume of water delivered by pipet (Calculated from density formula) D- (Show set-up) 13.…
A: Mass of water present in the beaker = 24.826 g Volume of the pipet = 25 ml Density of water = Mass…
Q: what is the biggest buret size that'll deliver 4.8mL with a relative error less than or equal to…
A: Answer - According to the question - Given - volume need to be delivered is 4.8 mL with an accuracy…
Q: In the vapor deposition method, solids are usually converted into solutions using their solvents. *…
A: A question based on general chemistry that is to be accomplished.
Q: Consider the following two standard deviation values: 0.100 grams/mol and 1.00 grams/mol. Which of…
A: Standard deviation is defined as the variation of a quantity from its recorded mean value. It is…
Q: State whether the errors in (a)–(d) are random or systematic: a. A 25-mL transfer pipet consistently…
A:
Q: Which is an example of an indeterminate error? Wrong dilution of sample solution Overshooting…
A: Indeterminate errors are also called accidental errors or random errors which are beyond the scope…
Q: Test Tube Volume Volume of Water Added Syringe Reading (mL) V w Total Air Volume Trial (mL) V t (mL)…
A: Boyel's law : It states that the temperature always remains constant when the volume of given mass…
Q: Thereproducibility of replicate measurements may be expressed by: 1. ORelative error 2. OAbsolute…
A: A multiple choice question based on statistical analysis, which is to be accomplished.
Q: The inside diameter of an open cylindrical tank was measured. The results of four replicate…
A:
Q: Give two examples of the Scale Factor Error (one of the types of systematic error).
A: We need to give two examples of scale factor error.
Q: A 4.00 (+0.01) mL Class A transfer pipet is used to transfer 4,00 mL of a 0.294 (40.005) M Cu stock…
A:
Q: If you were pipetting 17.0 mL, what is the percent error in the pipet? I know that Volumetric…
A: To figure out percent error in the pipet we need to figure out maximum error in the pipet then we…
Q: State whether the errors in (a)-(d) are random or systematic. If it is systematic, identify if it is…
A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: 4. For a constant head laboratory permeability test on sand, the following data were given: Length…
A: Hi thanks for the question
Q: The reproducibility of replicate measurements may be expressed by: 1. ORelative error 2. O Absolute…
A: Reproducibility may be referred as reliability or degree of stability as per data when repeated…
Q: 1. Samples that should not be stored should be prepared/analyzed as soon as possible, especially for…
A: 1. Answer - The correct option is (c) Conductivity According to the question - Samples that should…
Q: Why is it necessary to calibrate lab instruments such as a thermometer and volumetric glassware?
A: An instrument that has the capability to measure the temperatures or temperature changes in a…
Q: volumertic and non-volumetric quantitative analytical menthods
A: Volumertic and non-volumetric quantitative analytical methods.
Q: Calculate the suspended solids in mg/L given the following data: Weight of crucible: 21.0256 g,…
A: Given, Weight of crucible: 21.0256 g Weight of crucible and dry solids: 21.0301 g Weight of…
Q: 1. Standardization of Sodium Hydroxide Primary Standard used: Formula Mass of Primary Standard: %…
A: In the given question we have to do the standardization of NaOH and to calculate the required NaOH…
Q: I am supposed to calculate Average absolute deviation (%). I am not sure if 7.16 is the final…
A:
Q: a) The total hardness of this sample b) The percentage error in this sample
A: Topic-- Hardness of water Hardness of water-- The simple definition of water hardness is the amount…
Q: Limitation of accuracy of the following instruments: a. Erlenmeyer flask b. beaker
A: Erlenmeyer flask, and beaker are used for Reaction , filteration , mixing etc. but not for…
Q: Estimated volume of crucible 25.0 mL measured volume of crucible 23.0 mL percent error of…
A: Percent error or percentage error expresses as a percentage the difference between an approximate or…
Q: You have a stock solution of 150.0±0.3 mg SO²/mL that has been certified by the manufacturer. You…
A:
Q: 9) The following results were obtained in the determination of Vitamin E mass in tablet samples.…
A:
Q: Determine the percentage error and the concentration of the prepared NaOH given the following data:…
A: To determine the percentage error and the concentration of prepared NaOH
Q: What should you write in your lab notebook if you measure 10 mL of a liquid as accurately as you can…
A: There are different types of glassware which are being used while performing any sort of experiment…
Q: A 4.00 (40.01) mL Class A transfer pipet is used to transfer 4.00 mL of a 0.289 (+0.005) M Cu+ stock…
A: Given that Initial volume of Cu2+ = 4.00 (±0.01) mL Initial molarity 0f Cu2+ = 0.289 (±0.005) M…
Q: What piece of equipment should you use in order to obtain the mass of the weighing form? A…
A: A triple beam balance is used to measure mass of the weighing form with precisely. If you want to…
Q: Two methods were used to measure the arsenic level (ppb) in drinking water. Quantity Mean arsenic…
A: First, we need to calculate the F value and T-value, and compare the standard deviations for the two…
Q: Can you give 5 laboratory apparatuses examples on each classifications?
A: A. Measuring type : In laboratory many measuring cylinder are used. These are used to measure liquid…
Q: There are no different between volumetric and graduated pipettes
A: false there is a difference between between graduated pipette and volumetric pipette graduated…
Q: test tube mL Nickel standard ML 0.6 m H2SO4 blank 10.0 mL 2.0 mL 8.0 mL 2 4.0mL l6.0 mL 3 l6.0 mL…
A:
Q: A 4.00 (±0.01) mL Class A transfer pipet is used to transfer 4.00 mL of a 0.264 (+0.005) M Cu2+…
A:
Q: A pharmacist is asked to weigh 140 mg of lidocaine powder on the standard balance. The maximum…
A: Given that, Sensitivity requirement = 3mg Acceptable error = 5% To be calculated, Minimum weighable…
Q: reading the measurements provided by the volumetric apparatus, the eye must be at the same level as…
A:
Q: Why is the pipette more precise than a burette when measuring?
A: Burettes are larger than a pipette, it has a stopcock at the bottom to control the release of…
Q: Compare the value you calculated with the actual value (-601.8 kJ/mol). Show your determination of…
A: In a reaction, for the reactant to convert to product, some amount of heat is transferred into or…
Q: 5. Based on the tolerance table for volumetric glassware, the volume of a 25 mL volumetric pipet and…
A: Calibrated volumetric glasswares are required to get accurate results and data while performing any…
Q: we dilute unknown sample of 25ml to 100ml And want to find error propagation associated with it. The…
A: The error propagation during the dilution process is to be calculated.
Q: You have a stock solution certified by a manufacturer to contain 220.0 + 0.4 ug So /ml. You would…
A: Method A: Dilution of 10.00 mL (transfer pipet) 215.0 g/mL stock solution to 100 mL (vloumetric…
Q: A certified reference material of lead in calcium carbonate is analyzed by a laboratory and found to…
A:
Q: Describe the procedure involved in flame test. Subject: Analytic chemistry
A: The flame test is used to detect the presence of elements, based on each element's characteristic…
Q: Estimated volume of crucible 25.0 mL measured volume of crucible 23.0 mL percent error of…
A: % error=accepted value-experimental valueaccepted valuex100 %
1) determine the glassware that can be used to deliver 4.5mL with an absolute error:
a) ≤ 0.15 mL
b) ≤ 0.02 mL
c) ≤ 0.07 mL
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- Current Attempt in Progress From the curves shown in Animated Figure and using the following Equation, determine the rate of recrystallization for pure copper at the several temperatures. Make a plot of In(rate) versus the reciprocal of temperature (in K-1). (a) Determine the activation energy for this recrystallization process. (See Section FACTORS THAT INFLUENCE DIFFUSION.) (b) By extrapolation, estimate the length of time required for 50% recrystallization at room temperature, 20°C (293 K). (a) i kJ/mol (b) i daysAn excess of 0.34 mg Pb is obtained from an assay test determined in an analysis. What is the percent relative error in ppt if the mass of the sample is 550 g?A student wanted to determine the moisture content of a solid sample using gravimetric methods following the AOAC 930.15 method. The following data were obtained: mass of crucible (container): 24.6743 g initial mass of crucible and sample: 34.2134 g final mass of crucible and sample: 32.0567 g Calculate the %moisture of this sample. Show your entire solving process. You may upload a photo of your solution or you may just type it in.
- Amylum, commonly known as starch is a white powder with variable molecular formula due to the different number of repeating sugar units based on the plant that it is obtained from. A sample of amylum in the form of spherical beads was subjected to series of analyses to determine physicochemical properties in the quality control unit of a factory. From the results each bead is found to have a 4.5 mL volume and 1.47 g/mL density. 4 of the beads were placed in a reaction chamber combusted, as a result, 43.1 g CO2 and 14.7 g H2O were obtained. If the molecular weight of the amylum is 972.84 g/mol how many repeating units the starch molecule consist and what is the molecular formula of the starch? [Empirical Formula=CxHyOz, Repeating unit=n, Molecular Formula=( CxHyOz)*n= CnxHnyOnz]Analyze each statement (A and B) whether they are true or false. Use the choices below in answering each item; A statement A is true B statement B is true C both A and B are true D neither A nor B are true (A) A dispersing agent such as Na-hexametaphosphate is needed prior to soil textural analysis. (B) particles greater than 2.0 mm is included in the analysis of soil texture.Part B (Trial #1) Part C (Trial #2) Mass of empty evaporation dish 154.48 g 158.34 g Volume of sodium chloride solution added to evaporation dish 10.0 mL 10.0 mL Mass of evaporation dish containing sodium chloride crystals after evaporating the water and drying 154.94 g 159.85 g Determine the average mass/volume % of salt in water.
- Standard deviation 0.6318 mL, 0.1216 mL, 0.1056 mL, 0.0681 mL, 0.0056 mL Mean-0.18654 mLSolid particles in water may exist in 3 ways - dissolved, dispersed, or suspended. (True/False) When a previously dissolved solid separates from water either via chemical reaction or a change in certain condition like pH or temperature, it forms a______.Trituration is a process of reducing particle size which involves the addition of an appropriate solvent. Select one: True False
- You have run analysis on an unknown acetaminophen sample. Your results showed the concentration of acetaminophen in the unknown was 35.9%. The actual concentration of acetaminophen in the unknown was 49.0%. What is the error % for this analysis? Answer to 1 decimal place.1.5 x 103 uL ------> mLQUESTION 16 Match the correct choices with the given. For gravimetric analysis, use this data to answer the questions. |Trial 1 0.6020 g 24.8405 g 24.8451 g 24.8422 Trial 2 0.5021 g 22.8165 g 22.8165 g Trial 3 0.5018 g 22.8169 g 22.8169 g |Weight of Sample Weight of Crucible and Ba$O, 8 24.8422 g Constant Weight of Crucible & Sample 24.8422 g 22.8165 g 22.8169 g Weight of Crucible 24.3181 22.3593 g 22.3641 g 24.3160 g 24.3142 g 24.3142 g 24.3142 g 24.3142 g 22.3523 g 22.3534 g 22.3532 g 22.3532 g 22.3612 g 22.3605 g 22.3605 g 22.3605 g Constant Weight of Crucible 22.3532 g 22.3605 g Weight of BaSo, |% so,2- Average Standard deviation Relative standard deviation A. 2.65 Average of the % (w/w) SO42- B. to decompose the solid and form a compound of known composition and to remove the solvent and any non-volatile species Standard deviation of the % (w/w) So2- Relative standard deviation of the C. reprecipitation % (w/w) SO42- D. formation of small crystals This is a drastic but effective…